JVC 0205NYMCREBET - Manual (Page 58)

26
En
glish
Troubleshooting
• If you are having a problem with your System, check this list for a possible solution before calling for service.
• If you cannot solve the problem from the hints given here, or the System has been physically damaged, call a qualified person, such as
your dealer, for service.
Symptom Possible Cause Action
No sound is heard. • Connections are incorrect, or loose.
• Headphones are connected.
• Check all connections and make corrections.
(See pages 4 to 6.)
• Disconnect the headphones.
Poor radio reception • The antenna is disconnected.
• The AM Loop Antenna is too close to the Sys-
tem.
• The FM Wire Antenna is not properly
extended and positioned.
• Reconnect the antenna securely.
• Change the position and direction of the AM
Loop Antenna.
• Extend FM Wire Antenna to the best reception
position.
The disc tray does not open. • The AC power cord is not plugged in.
• Tray is locked. • Plug the AC power cord.
• Unlock the tray. (See page 15.)
The CD skips. The CD is dirty or scratched. Clean or replace the CD. (See page 25.)
The CD does not play. The CD is upside down. Put the CD in with the label side up.
The MP3 disc does not play. • No MP3 files are recorded on the disc.
• MP3 files do not have the file extension —
.MP3, .Mp3, .mP3, or .mp3 in thier file names.
• MP3 files are not recorded in the format com-
pliant with ISO 9660 Level 1 or Level 2.
Replace the disc.
The readout time of the MP3 disc is too long. The readout time varies with the complexity of
the recording configuration. Do not use too many hierarchies and folders when
recording. Also, do not record any other types of au-
dio tracks together with MP3 files. (See page 11.)
The cassette holder cannot be opened. During tape playing, the power cord was unplugged. Plug in the power cord, and turn on the System.
Unable to record. Cassette record protect tabs are removed. Cover holes on back edge of cassette with tape.
Unable to operate the Remote Control. • The path between the Remote Control and the
sensor on the Unit is blocked.
• The batteries have lost their charge.
• Remove the obstruction.
• Replace the batteries.
Operations are disabled. The built-in microprocessor has malfunctioned due
to external electrical interference. Unplug the System then plug it back in.
Amplifier Unit
Output Power 140 W per channel, min. RMS, driven Dimensions 270 mm × 306 mm × 456 mm (W/H/D)
into 6
Ω at 1kHz, with no more than
Mass Approx. 8.6 kg
10% total harmonic distortion Speaker Specifications (each unit)
(IEC 268-3) SP-MXKC4
Input Sensitivity/Impedance (1 kHz) Type 3-way bass-reflex type
AUX IN 400 mV/50 k Ω Speaker Unit Woofer: 16 cm cone × 1
Speaker terminals 6
Ω - 16 Ω
Mid: 5cm cone × 1
Phones 32
Ω - 1 kΩ
Tweeter; 2cm dome × 1
15 mW/ch output into 32
Ω
Power Handling Capacity 140 W
Cassette Deck Section Impedance 6 Ω
Frequency Response Frequency Range 45 Hz - 22 000 Hz
Type I (NORMAL) 63 Hz - 12 500 Hz Sound pressure level 87 dB/W·m
Wow And Flutter 0.15% (WRMS) Dimensions 266 mm × 333 mm × 241 mm (W/H/D)
CD Player Mass Approx. 3.9 kg
CD Capacity 3 CDs Accessories
Dynamic Range 85 dB AM Loop Antenna (1)
Signal-To-Noise Ratio 85 dB Remote Control (1)
Wow And Flutter Unmeasurable Batteries R6P (SUM-3)/AA (15F) (2)
Tuner FM Wire Antenna (1)
FM Tuner AC Plug Adaptor (1)
Tuning Range 87.5 MHz - 108.0 MHz Power Specifications
(at AM10 kHz channel space) Power Requirements AC 110 V/127 V/220 V/230 V-240 V ,
87.50 MHz - 108.00 MHz
(at AM9 kHz channel space) adjustable with voltage selector,
50 Hz/60 Hz
AM Tuner Power Consumption 140 W (power on mode)
Tuning Range 530 kHz - 1710 kHz (at AM10 kHz 22 W (in Standby mode)
channel space)
531 kHz - 1710 kHz (at AM9 kHz
Design and specifications are subject to change without notice.
channel space)
Specification
MX-KC4(UW).book Page 26 Thursday, January 20, 2005 6:51 PM