JVC SP-UXG70 - Manual (Page 38)

34
Additional Information
Learning More about This System
Connections (see pages 3 to 5)
• Make sure the antenna conductors do not touch any other
terminals, connecting cords or the power cord. Also, keep
the antennas away from metallic parts of the System,
connecting cords, and the AC power cord. This could cause
poor reception.
• Use only speakers with the same speaker impedance as
indicated by the speaker terminals on the rear of the System.
• The speakers are magnetically shielded to avoid color
distortions on TVs. However, if not installed properly, it
may cause color distortions. So, pay attention to the
following when installing the speakers.
– When placing the speakers near a TV set, turn off the
TV’s main power switch or unplug it before installing the
speakers.
Then wait at least 30 minutes before turning on the TV’s
main power switch again.
– Some TVs may still be affected even though you have
followed the above instructions. If this happens, move
the speakers away from the TV.
• When a portable audio device is connected to the LINE IN
jack, sound will come out of the speakers and headphones.
However, no sound will come out of the LINE OUT jack.
Daily Operations—Playback (see pages 7 to 11)
Listening to the Radio:
• If you store a new station into an occupied preset number,
the previously stored station in that number will be erased.
• When you unplug the AC power cord or if a power failure
occurs, the preset stations will be erased in a few days. If
this happens, preset the stations again.
Listening to the TV Sound:
• When you use this function, connect the System and TV
with the Scart cable.
Playing Back a Disc:
• On some DVD, SVCD, or VCD discs, the actual operations
may be different from what is explained in this manual, due
to the programming and disc structure; such differences are
not a malfunction of this System.
• When discs* in more than one tray are loaded on the disc
trays, they are played in sequence as follows. (When DVD
Video, DVD Audio or SVCD/VCD with PBC is loaded in
the System, playback of the disc next to these discs will not
start.):
Ex.: When DISC 2 is selected:
DISC 2
]
DISC 3
]
DISC 4
]
DISC 5
]
DISC 1
]
(then stops)
* When no disc is loaded on the disc tray, that disc number
is skipped.
• You can exchange discs while playing or selecting another
disc.
• Some DVD Audio discs prohibit downmix. When you
playback such a disc, “LR ONLY” appears on the display
and the System plays back the left front and right front
signals.
• When playing back a DVD Audio disc recorded in MLP
(Meridian Lossless Packing; a lossless audio compression
system that can completely recreate the PCM signal), the
signals are recognized as the linear PCM signals, however,
no indicator lights up on the display.
• This System can recognize up to 4 000 tracks in a disc.
Also, the System can recognize up to 150 tracks per group
and up to 99 groups in a disc.
– If there are any unplayable files in a folder, those files are
also counted in the total file number.
– Playable files which do not belong to any groups are
handled as Group 1.
• For DVD-VR playback...
– This System can play only a disc of UDF-Bridge format.
– For details about DVD-VR format and playlist, refer to
the manual of the recording equipment.
– You cannot use reverse slow motion, Program Play, or
Random Play.
• For MP3/WMA playback...
– MP3/WMA discs require a longer readout time than
regular CDs. (It depends on the complexity of the group/
file configuration.)
– Some MP3/WMA files cannot be played back and will
be skipped. This results from their recording processes
and conditions.
– This System can play only a disc of ISO 9660 Level 1 or
Level 2.
– This System can playback MP3/WMA files with the
extension code <.mp3> or <.wma> (regardless of the
letter case—upper/lower).
– It is recommended that you make each MP3/WMA file at
a sampling rate of 44.1 kHz and at a bit rate of 128 kbps.
This System cannot playback files made at a bit rate of
less than 64 kbps.
UX-G70[B].book Page 34 Monday, April 17, 2006 1:41 PM