JVC LM-H191 - Manual (Page 10)

9
ENGLISH
Specification of the Y/C terminal
Connect it to the S-video output
terminal.
Pin No. Input signal Pin No. Input signal Pin No. Input signal
1 T.M.D.S Data 2– 9 T.M.D.S Data 1– 17 T.M.D.S Data 0–
2 T.M.D.S Data 2+ 10 T.M.D.S Data 1+ 18 T.M.D.S Data 0+
3 T.M.D.S Data 2 shield 11 T.M.D.S Data 1 shield 19 T.M.D.S Data 0 shield
4 NC 12 NC 20 NC
5 NC 13 NC 21 NC
6 DDC Clock 14 +5 V Power 22 T.M.D.S Clock shield
7 DDC Data 15 GND 23 T.M.D.S Clock+
8 NC 16 Hot Plug Detect 24 T.M.D.S Clock–
Pin No. Input signal
1 GND (Y)
2 GND (C)
3 Y
4 C
Pin No. Input signal Pin No. Input signal
1 Red 9 +5 V
2 Green 10 GND
3 Blue 11 GND
4 – 12 DDC Data
5 GND 13 Horizontal/
composite sync
6 GND 14 Vertical sync
7 GND 15 DDC Clock
8 GND External GND
7 Available signals
Signal type
Frequency
Status display*
Input terminal
Horizontal (kHz) Vertical (Hz)
VIDEO 1
IN / Y/C
VIDEO
2 IN
RGB DVI-D
NTSC (3.58) 15.734 (60/)59.94 NTSC
NTSC (Y/C)
√ √ – –
BW/60 15.734 (60/)59.94 BW60 √ √ – –
PAL 15.625 50 PAL
PAL (Y/C)
√ √ – –
BW/50 15.625 50 BW50 √ √ – –
480/60p 31.5/31.469 60/50.94 640x480 60Hz – – √ –
576/50p 31.25 50 640x576 50Hz – – √ –
VGA 31.47 59.94 640x480 60Hz – – √ √
VGA_TEXT 31.47 70.08 720x400 70Hz – – √ –
SVGA 35.15 56.25 800x600 56Hz – – √ –
37.879 60.317 800x600 60Hz – – √ √
XGA 48.363 60.004 1024x768 60Hz – – √ √
56.476 70.069 1024x768 70Hz – – √ –
WXGA 47.396 59.99 1280x768 60Hz – – √ √
SXGA 63.981 60.02 1280x1024 60Hz – – √ √
√: Acceptable
—: Not acceptable
• Some signals may not be displayed normally even if its frequency is within
the acceptable range ( ☞ “Horizontal/vertical frequency (computer signal)” on
page 15).
* About the Status Display
When “STATUS DISPLAY” (
☞ page 12) is set to “AUTO,” the status is displayed for
about 3 seconds in the following cases:
– When you press the INPUT SELECT button of the current input
– When you change the input
– When the signal condition of the current input changes
– When you turn on the monitor
• “NO SYNC” is displayed when no video signal comes in.
• “Out of range” is displayed for a noncompliant video signal input.
Specification of the DVI-D terminal
Connect it to the DVI-D output terminal on a personal computer.
Specification of the RGB terminal
Connect it to the analog RGB output
terminal (D-sub 15-pin) on a personal
computer.
LMH191EA_EN.indd 9 LMH191EA_EN.indd 9 08.4.18 0:45:49 PM 08.4.18 0:45:49 PM