beautypg.com

Video recording & playback, Video recording, Basic recording – JVC Digital Video Camera GR-D24 User Manual

Page 10: Lcd monitor and viewfinder, Tape remaining time, Zooming, Pg. 10)

background image

10

EN

MasterPage: Heading0_Left

VIDEO RECORDING

NOTE:

Before continuing, perform the procedures listed below:

Power (੬ pg. 6)

● Loading a Cassette (੬ pg. 9)

1

Remove the lens cap.

2

Open the LCD monitor fully. (See the right column)

3

Set the Power Switch to “A” or “M” while pressing

down the Lock Button located on the switch.

● The POWER/CHARGE lamp lights and the camcorder

enters the Record-Standby mode. “PAUSE” is displayed.

● To record in LP (Long Play) mode, ੬ pg. 14, 15.

4

To start recording, press the Recording Start/Stop

Button. The “T REC” appears on the display while
recording is in progress.

5

To stop recording, press the Recording Start/Stop

Button again. The camcorder re-enters the Record-
Standby mode.

NOTES:

● The image will not appear simultaneously on the LCD

monitor and the viewfinder.

● If the Record-Standby mode continues for 5 minutes, the

camcorder’s power shuts off automatically. To turn the
camcorder on again, push back and pull out the viewfinder
again or close and re-open the LCD monitor.

● LCD monitor/viewfinder indications:

• When power is supplied from a battery: the “

battery indicator is displayed. (

੬ pg. 31)

• When power is supplied from an AC outlet: the “

battery indicator does not appear.

● When a blank portion is left between recorded scenes on

the tape, the time code is interrupted and errors may occur
when editing the tape. To avoid this, refer to “Recording
From The Middle Of A Tape” (

੬ pg. 11).

● To turn the beep sounds off, ੬ pg. 14, 16.

For other notes, pg. 27.

LCD Monitor And Viewfinder

While using the LCD monitor:
Make sure the viewfinder is pushed back in. Press the
Monitor Opening Button and open the LCD monitor fully.
It can rotate 270° (90° downward, 180° upward).

While using the viewfinder:
Make sure the LCD monitor is closed and locked. Pull out
the viewfinder fully.

● Be sure to pull out the viewfinder until you hear a click,

otherwise it may be pushed back in during use.

NOTES:

● The image will not appear simultaneously on the LCD

monitor and the viewfinder. When the viewfinder is pulled
out while the LCD monitor is opened, you can select which
one to use. Set “PRIORITY” to the desired mode in
SYSTEM Menu. (

੬ pg. 14, 16)

● Coloured bright spots may appear all over the LCD monitor or

the viewfinder. However, this is not a malfunction. (

੬ pg. 30)

Tape Remaining Time

Approximate tape remaining time appears on the display.
“– h – – m” means the camcorder is calculating the
remaining time. When the remaining time reaches
2 minutes, the indication starts blinking.

Zooming

Produces the zoom in/out effect, or an instantaneous
change in image magnification.

Zoom In
Slide the Power Zoom Lever towards “T”.

Zoom Out
Slide the Power Zoom Lever towards “W”.

● The further you slide the Power Zoom Lever, the quicker the

zoom action.

Basic Recording

POWER/CHARGE lamp

Recording Start/Stop Button

Power Switch

Lock Button

Power Zoom Lever

Push.

Monitor Opening Button

0h 25 m

– h– – m

1 h 0 m

0 h 3 m

0 h 2 m

0 h 1 m

0 h 0 m

0 h 5 9 m

(Blinking)

(Blinking)

(Blinking)

(Now calculating)

VIDEO RECORDING & PLAYBACK

GR-D33EK_05Video.fm Page 10 Friday, October 31, 2003 4:21 PM