JBL 2.4G AW - Manual (Page 9)

9
English
Adjustable wall brackets are included for the two speakers and
transmitter module. The included bracket are for wall-mounting only.
It is not to be used for ceiling mounting. Ceiling mounting of the
Control 2.4G AW transmitter and/or speakers is not recommended,
regardless of bracket used.
Wall-Mounting the Speakers
Using Wall Brackets Provided
Important safety note: Proper selection of mounting hardware not
included herein, and proper assembly and installation of brackets,
in cluding, but not limited to, selection of appropriate weight-bearing
support and bracket use with the specified speaker only is the
exclusive responsibility of the customer. Manufacturer disclaims any
liability for the selection of mounting hardware and/or bracket
installation.
Exploded
A. Loosen and remove the molded nut (2) by turning it counter
clockwise. Use the supplied metal bar (5) if necessary by inserting
it in one of the holes on the molded nut (2).
B. Pull the ball/shaft (3) out of the wall bracket (4).
C. Slide on the molded nut (2) onto the ball/shaft (3) with threaded
opening facing the ball, and thread on the metal nut (1) all the way
onto the ball/shaft (3), with the nut’s (1) ”knurled” surface facing
away from the ball.
D. Screw on the ball/shaft (3) into the threaded 1/4"-20 insert on the
back of the speaker cabinet (6) until it is fully seated against the
bottom of the insert. Back out the ball-shaft assembly 1/2 of a turn
and tighten the nut against the speaker. If the ball and shaft
assembly is not backed out before tightening the nut, performing
Step G below may dislodge the threaded insert in the speaker
housing and permanently damage the speaker.
E. Tighten the ”knurled” nut (1) using a crescent wrench until it is
firmly seated against the back of the speaker and has fully locked
the ball/shaft (3) and the speaker cabinet together. Pleace note
that once this nut is tightened, it may embed some marks on the
back of the speaker where the attachment is made. However,
these marks will be covered by the nut (1).
F. The back-up cord (8) is provided as an additional measure to
prevent the fall of the speaker in case the speaker becomes
detached from the wall bracket.
One of the two lower screws (9) that attach the wall bracket (4) to
the wall will need to go through the eyelet (11) at the end of the cord
before going through the wall bracket hole. Mount the wall bracket
(4) onto a wood stud on the wall, using #10, minimum 1-inch-long,
panhead wood screws. Make sure that all 4 screws are driven into
the stud, not drywall. If the bracket needs to be mounted on
drywall, the use of properly selected and installed wall-anchors
and screws is essential. Make sure that the screw head is at least
9mm (0.36 or approximately 3/8 of an inch) or larger in diameter so
that it can properly hold the backup cord eyelet (11).
G. Holding the speaker cabinet (7) with both hands, reinsert the ball
portion of the ball/shaft (3) into the wall bracket (4).
H. Hand-tighten the molded nut (2) while positioning the speaker for
the intended orientation.
I. Once the orientation of the speaker is finalized, use the metal bar
(5) in one of the holes on the molded nut (2) and tighten securely.
J. Securely attach the other end (10) of the backup cord (8) to the
Control 2.4G, by engaging it through the bar (12) on the back
speaker.
Also included with the system is a wall-mount holder for the active
speaker’s power supply. If desired, you may attach this holder to the
wall and insert the speaker’s power supply.
Please note that while the Control 2.4G AW is an all-weather outdoor
loud-speaker, it is not waterproof. Neither the speakers nor power
supply should be submerged or directly exposed to water, ice, snow
or sustained moisture.Do not install the transmitter module outdoors.
WALL AND STAND PLACEMENT
TO LEFT SPEAKER
+ –
TO LEFT SPEAKER
+ –
CORRECT INCORRECT
0039CSK JBL On Air Control_2.4_AW_ENG_v5_GODKENDT:34199_Control_2_4G_Eng 10/06/08 15:57 Side 9