JVC RX-8020VBK - Manual (Page 30)

27
Setting the AM Tuner Interval Spacing
Some countries space AM stations 9 kHz apart, and other countries use
10 kHz spacing.
To select the 10 kHz interval:
Be sure the receiver is turned off, but is plugged into an AC outlet. Hold
down FM/AM TUNING
5 and press STANDBY/ON . “10k
STEP” appears on the display. Now the 10 kHz interval is selected.
To change back to the 9 kHz interval:
Be sure the receiver is turned off, but is plugged into an AC outlet. Hold
down FM/AM TUNING
∞ and press STANDBY/ON . “9k STEP”
appears on the display. Now the 9 kHz interval is selected.
Tuning into Stations Manually
On the front panel:
1. Press FM/AM to select the band
(FM or AM).
The FM/AM lamp on the front panel button
lights up. The last received station of the
selected band is tuned in.
• Each time you press the button, the band
alternates between FM and AM.
2. Press FM/AM TUNING
5 or ∞
until you find the frequency you
want.
• Pressing FM/AM TUNING 5 increases
the frequency.
• Pressing FM/AM TUNING ∞ decreases
the frequency.
From the remote control:
1. Press FM/AM to select the band
(FM or AM).
The FM/AM lamp on the front panel button
lights up. The last received station of the
selected band is tuned in.
• Each time you press the button, the band
alternates between FM and AM.
+
FM/AM TUNING
STANDBY/ON
STANDBY
FM/AM TUNING
+
STANDBY/ON
STANDBY
FM/AM
ANALOG
VOLUME
TUNED STEREO L R
SPEAKERS 1
FM/AM TUNING
FM / AM
Receiving Radio Broadcasts
You can browse through all the stations or use the preset function to go immediately to a particular station.
2. Press TUNING UP
3 or
TUNING DOWN
2 until
you find the frequency you
want.
• Pressing TUNING UP 3 increases the
frequency.
• Pressing TUNING DOWN 2 decreases
the frequency.
Notes:
• When a station of sufficient signal strength is tuned in, the TUNED
indicator lights up on the display.
• When an FM stereo program is received, the STEREO indicator
also lights up.
• When you hold and then release the button in step 2, the frequency
keeps changing until a station is tuned in.
DOWN – TUNING – UP
SET
/REW FF/ PAUSE
MEMORY
Using Preset Tuning
Once a station is assigned to a channel number, the station can be
quickly tuned in. You can preset up to 30 FM and 15 AM stations.
To store the preset stations
Before you start, remember...
There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 2 again.
On the front panel ONLY:
1. Tune in the station you want to preset (see
“Tuning into Stations Manually” on the left).
• If you want to store the FM reception mode for this station,
select the FM reception mode you want. See “Selecting the
FM Reception Mode” on page 28.
2. Press MEMORY.
The channel number position starts flashing on the display for
about 10 seconds.
3. Press FM/AM PRESET
5 or ∞ to
select a channel number while the
channel number position is
flashing.
ANALOG
VOLUME
TUNED STEREO L R
SPEAKERS 1
ANALOG
VOLUME
TUNED STEREO L R
SPEAKERS 1
FM/AM PRESET
ANALOG
VOLUME
TUNED STEREO L R
SPEAKERS 1
EN27-29.RX-8020V[UJ]_f 02.5.22, 9:48 AM 27