JBL Professional DPC-2 - Manual (Page 9)

9 JBL Professional
VP SERIES SYSTEMS SPECIFICATIONS
VP7210/95DP
Specifications:
Frequency Response (+/-3dB): 80 Hz - 20 kHz
Frequency Range (-10dB): 50 Hz - 20 kHz
Coverage Pattern: 90° x 50° rotatable waveguide
Directivity Factor (Q): 10
Directivity Index (DI): 10 dB
Max Peak Output: 132 dB SPL 1m
Transducer Section:
Low Frequency Section: JBL 2261FF, 254 mm (10 in) dia., 76 mm (3 in) Dual Coil
neodymium Differential Drive ® , Direct Cooled
Bandpass Nominal Impedance: 2 x 2 ohms
High Frequency: JBL2452H-SL, 100 mm (4 in) titanium damped dia-
phragm, 1.5 in. exit
Bandpass Nominal Impedance: 8 ohms
System:
DPC-2 Internal Amplification Output
(at nominal load):
1750 Watts Peak (875 Watts Continuous)
DPC-2 Output (Continuous IEC shaped pink
noise into rated load impedance):
750LF/125HF Watts
DPC-2 Output Section: LF: Dual Bridged Technology ™ , Class D
HF: Bridged Class D
Audio Input Connector: XLR with loop-through
User Controls: 80 Hz Subwoofer High Pass Filter, Enable/Disable
0-16 dB input Attenuator with 32 precision 0.5 dB steps
Signal Processing: DSP based, resident in Input Module.
System Management: DSP based limiters for mechanical and thermal
protection
AC Power Operating Range: 90-132VAC/216-264VAC, 50/60 Hz
AC Line Voltage: 50/60 Hz, User Select; 120V/240V (-15%, +10%)
AC Input Connector: Neutrik PowerCon (NAC 3MPA)
AC Loop-Thru: Neutrik PowerCon (NAC 3MPB)
AC Current Requirement: 6A per system at 120V, 3A per system at 240V
Enclosure:
Box Construction: 5/8 in. multi-ply exterior grade Baltic birch. Internally
braced. Black DuraFlex ™ finish
Suspension System: 10 M10 fittings, 2 x M6 pullback on rear
Grille: 14 Gauge Black, powder-coated perforated steel with
foam backing
Dimensions (H x W x D): 521 x 293 x 303 mm
20.5 x 11.5 x 11.9 in.
Net Weight: 18.4 kg (40.5 lbs)
VP7212MDP
Specifications:
Frequency Response (+/-3dB): 60 Hz - 18 kHz
Frequency Range (-10dB): 55 Hz - 20 kHz
Coverage Pattern: 50° x 90° rotatable waveguide
Directivity Factor (Q): 15.8
Directivity Index (DI): 12 dB
Max Peak Output: 137 dB SPL 1m
Transducer Section:
Low Frequency Section: JBL 2265G, 381 mm (15 in) dia., 76 mm (3 in) Dual Coil
neodymium Differential Drive®, Direct Cooled
Bandpass Nominal Impedance: 4 ohms
High Frequency: JBL2452H-SL, 100 mm (4 in) titanium damped dia-
phragm, 1.5 in. exit
Bandpass Nominal Impedance: 8 ohms
System:
DP2 Internal Amplification Output
(at nominal load):
1750 Watts Peak (875 Watts Continuous)
DPC-2 Output (Continuous IEC shaped pink
noise into rated load impedance):
750LF/125HF Watts
DPC-2 Output Section: LF: Dual Bridged Technology ™ , Class D
HF: Bridged Class D
Audio Input Connector: XLR with loop-through
User Controls: 80 Hz Subwoofer High Pass Filter, Enable/Disable
0-16 dB input Attenuator with 32 precision 0.5 dB steps
Signal Processing: DSP based, resident in Input Module.
System Management: DSP based limiters for mechanical and thermal
protection
AC Power Operating Range: 90-132VAC/216-264VAC, 50/60 Hz
AC Line Voltage: 50/60 Hz, User Select; 120V/240V (-15%, +10%)
AC Input Connector: Neutrik PowerCon (NAC 3MPA)
AC Loop-Thru: Neutrik PowerCon (NAC 3MPB)
AC Current Requirement: 6A per system at 120V, 3A per system at 240V
Enclosure:
Box Construction: 5/8 in. multi-ply exterior grade Baltic birch.
Internally braced. Black DuraFlex ™ finish
Suspension System : None
Grille: 14 Gauge Black, powder-coated perforated steel with
foam backing
Dimensions (H x W x D): 346 x 565 x 413 mm
13.6 x 22.3 x 16.2 in.
Net Weight: 20.7 kg (45.5 lbs)