Integra DTR-6.4/5.4 - Manual (Page 71)

71
Programming the commands of remote controllers for other devices into the remote
controller
4. Press and hold down the button (that corresponds to
the command you are programming) on the remote
controller of the other device until the Send/Learn
lamp on the remote controller flashes twice.
After flashing twice, the Send/Learn indicator will light again.
5. Repeat Steps 3 and 4 to transfer all the commands
you desire from the other remote controller and
program them to buttons on the remote controller
under the same Mode.
Repeat Steps 2 through 4 to program commands to a different Mode
(e.g., when programming from a different remote controller).
6. Press the Mode button that you pressed in step 2 to
complete the programming.
7. Operate the newly programmed buttons to make sure
the learning function was performed properly.
Notes:
• The remote controller codes for Integra/Onkyo compact disc
players, cassette tape decks, DVD players, and mini disc
recorder have already been programmed into buttons on the
remote controller. You may, however, use these buttons to
program the codes for other remote controllers. If you wish to
restore the Integra preset codes after you program new codes,
you must first erase the new codes.
• The remote controller has 357 memory slots (7 modes
× 51
buttons). Some remote controllers may have more commands
that can be remembered by the remote controller. In such cases,
it will be necessary for you to determine which commands are
more important than others.
• If the Send/Learn indicator quickly flashes three times and turns
off, then the remote controller has exited the programming
mode because either you have made a mistake during
programming or a time-out has occurred because no button has
been pressed. Resume from Step 2.
• If you try to program beyond the learning capacity of the remote
controller, the Send/Learn indicator flashes six times quickly,
and the remote controller exits the programming mode. Try
programming under a different Mode button.
• When you want to program a command to a button to which
you have already programmed a command, simply follow the
same procedure given and the previous programming for that
button will be overwritten.
• The remote controller uses infrared rays to send its commands,
as do most other remote controllers. Though most remote
controller codes can be memorized by the remote controller, be
aware that some remote controllers use systems that are quite
different from the remote controller and therefore may not be
able to be programmed.
• Some remote controllers have a single button that performs
multiple functions (for example, the function may change each
time the button is pressed). If this is the case, each function
must be programmed to a separate button on the remote
controller.
• Once you have transferred the commands from the other remote
controller, refer to the instruction manual that came with that
product for instructions on how to operate that product.
• Make sure both the remote controller and the other remote
controller have new batteries. If either of them has batteries that
are low, you may not be able to program the commands of the
other remote controller properly into the remote controller.
You can only erase memorized commands and not preset ones.
1. Press and hold down the Mode button for the
command, press the ENTER button, and then release
both buttons.
When you press the Mode button, the Send/Learn indicator
lights. When you press the ENTER button, the lamp turns off.
When you release the buttons, the lamp lights again.
2. Press and release the button for the command you
wish to erase.
When you press the button, the Send/Learn indicator turns off.
When you release the button, the lamp lights again.
3. Press and release the same button again.
The Send/Learn lamp slowly flashes twice. The memorized
command is erased.
Note:
If the Send/Learn indicator quickly flashes three times and turns off,
then the remote controller has exited the erasing mode because
either you have made a mistake during erasing or a time-out has
occurred because no button has been pressed. Resume from Step 1.
1. Press and hold down the desired Mode button, press
the ENTER button twice, and then release both
buttons.
When you press the Mode button, the Send/Learn indicator
lights. When you press the ENTER button, the lamp turns off.
When you release the buttons, the lamp slowly flashes twice and
then lights again.
2. Press and release the same Mode button again.
When you release the button, the Send/Learn indicator slowly
flashes twice. This erases all the commands memorized to the
Mode button.
Notes:
• If the Send/Learn indicator quickly flashes three times and turns
off, then the remote controller has exited the erasing mode
because either you have made a mistake during erasing or a
time-out has occurred because no button has been pressed.
Resume from Step 1.
• If many commands have been programmed to the Mode button,
then the Send/Learn indicator may remain lit for up to 20
seconds during Step 2. This is not a malfunction.
Erasing the programmed command from one
button
Erasing all the commands programmed under a
Mode button