Infinity Kappa Series 3-Way Component System 1.1cs - Manual (Page 3)

- 3 -
– + MID
REFERENCE STANDARD AUTOMOTIVE
Component System Crossover Network
TO LEFT MIDRANGE TO LEFT TWEETER TO RIGHT
TWEETER TO RIGHT MIDRANGE + + + + LO HI – – LO HI MID HI LO MID HI LO – –
TO RIGHT WOOFER
+ HI
LO
– TO LEFT WOOFER + HI
LO
–
FROM LEFT AMPLIFIERS FROM RIGHT AMPLIFIERS
+ – WOOFER + – MIDRANGE + – EMIT TWEETER + – + – + – EMIT TWEETER MIDRANGE WOOFER
–
+ HI
To RIGHT
Woofer
–
HI +
To LEFT
4" Midrange
– + HI –
To RIGHT
4" Midrange
To LEFT
Tweeter
–
To RIGHT
Tweeter
+ HI
+ MID
+ – + –
+
–
+
–
LEFT
RIGHT
+
LEFT
RIGHT
To Woofer Amplifier
RIGHT
To Midrange Amplifier
RIGHT
BLU BLU
BLU/WHT
GRY/
BLK
GRY
GRY/
WHT
GRY RED
RED/
BLK
RED
RED/
WHT
Remove Pigtail
–
+
–
+
LEFT
RIGHT
–
+
–
GRN
GRN/BLK
GRN/WHT
GRN Amplifier
(Tweeters)
❷
❶
❷
❶
To LEFT
Woofer
BLU/BLK
Amplifier
(Woofers)
Amplifier
(Midrange)
Figure 3. This application shows
connections for a Kappa1cs sys-
tem and three stereo amplifiers.
T WEETER I NSTALLATION
Figure 5. Installing a Kappa 1.1cs/653.1cs midrange driver
in a door panel.
Figure 6. After installing the surface-mount plate, slide the
Kappa1.1cs EMIT-N™ tweeter down on the plate to lock in
place.
RED RED
BLK BLK
– + MID
REFERENCE STANDARD AUTOMOTIVE
Component System Crossover Network
TO LEFT MIDRANGE TO LEFT TWEETER TO RIGHT
TWEETER TO RIGHT MIDRANGE + + + + LO HI – – LO HI MID HI LO MID HI LO – –
TO RIGHT WOOFER
+ HI
LO
– TO LEFT WOOFER + HI
LO
–
FROM LEFT AMPLIFIERS FROM RIGHT AMPLIFIERS
+ – WOOFER + – MIDRANGE + – EMIT TWEETER + – + – + – EMIT TWEETER MIDRANGE WOOFER
–
+ HI
To RIGHT
Woofer
–
HI +
To LEFT
4" Midrange
– + HI –
To RIGHT
4" Midrange
To LEFT
Tweeter
–
To RIGHT
Tweeter
+ HI
+ MID
– +
– +
+ –
+ –
+
–
+
–
To LEFT
Woofer
LEFT
RIGHT
+
LEFT
RIGHT
To Woofer Amplifier
RIGHT
BLU
BLU/BLK
BLU
BLU/WHT
GRY/
BLK
GRY
GRY/
WHT
GRY RED
RED/
BLK
RED
RED/
WHT
Connect Pigtail
Jumpers As Shown
–
+
–
Amplifier
(Tweeter & Mids)
GRN
GRN/BLK
GRN/WHT
GRN
Amplifier
(Woofers)
❶
❶
M IDRANGE I NSTALLATION
Figure 7. After sliding down the flush-mount clip onto the
back of the Kappa1.1cs EMIT-N tweeter, use the supplied
hardware to fasten the cup to the panel.
sacle = 70%
Bi-Amp
Tri-Amp
W OOFER I NSTALLATION
Figure 4. Installing a Kappa1.1cs/653.1cs woofer
above a deck or (with the enclosed spacer) below
a deck.
NOTE: Use the mounting clips as nuts to secure
the below-deck installation.
Figure 2. This application shows
connections for a Kappa1cs sys-
tem and two stereo amplifiers.
Kappa 653.1cs OM 7/14/98 10:10 AM Page 3