Ives 620 Series - Manual

829171-00(0) © 2006 Ingersoll-Rand Company Limited
602 and 702 Series Surface Continuous Hinges
Installation Instructions
829171-00
Check for proper operation. 3
Close door and check for
proper operation and
clearances.
A.
1/8”
1/8”
Mount hinge to frame. 1
Place frame leaf of hinge on face
of frame so that there is 1/8” gap
between top of hinge and
underside of frame header, and
1/16” gap between edge of the
frame and the center line of the
hinge barrel. Check to be sure
hinge leaf is square to frame with
1/16” gap from edge of frame to
centerline of hinge barrel the full
length of the hinge.
ALL HOLE LOCATIONS ON HINGE LEAF MUST BE FASTENED TO
FRAME FOR PROPER OPERATION. FAILURE TO INSTALL ALL
FASTENERS WILL VOID WARRANTY AND UL FIRE LABEL LISTINGS.
Frame
1/8”
1/16”
A.
B.
C.
With hinge held firmly and accurately
to frame, place 1/4”-20 x 3/4” self drilling
screws through cover clips and screw into frame through
mounting holes in hinge leaf. Cover clips should be located
at the top and bottom mounting holes, and equally spaced
along the length of the frame leaf.
Install remaining 1/4”-20 x 3/4” self drilling screws through
mounting holes in frame leaf.
NOTE: FOR THIN METAL FRAMES (18 GAUGE OR THINNER)
THE USE OF RIVET NUT STYLE FASTENERS IS RECOMMENDED.
IMPORTANT NOTE: FOR ALL UL
FIRE LABEL DOORS, 1/4”-20 X
1-3/4” STEEL THROUGH BOLTS
MUST BE USED FOR FASTENING
THE HINGE TO THE DOOR.
Move door into opening and place
door leaf of hinge on face of door so
that top of door is flush with top of
hinge and center line of hinge barrel
is 1/16” from edge of door.
A.
B.
NOTE: There should be 1/8” clearance between the top of
the door and the bottom of the frame header and 1/8”
clearance between the edge of the door and frame. An
angle block, jack or shims will be helpful in positioning the
door properly. Check to be sure hinge leaf is square to
door with 1/16” gap from edge of frame to centerline of
hinge barrel the full length of the hinge.
With hinge and door held firmly and accurately in place, use
1/4”-20 x 3/4” self drilling screws through cover clips and
screw into door through mounting holes in door leaf. Cover
clips should be located at top and bottom mounting holes,
and equally spaced along the length of the door leaf.
Install remaining 1/4”-20 x 3/4” self drilling screws through
mounting holes in door leaf.
Mount hinge to door. 2
1/8”
1/16”
Frame
Edge of
door
Note: Before proceeding, check to be sure that hinge is proper
size. Height of hinge should be 7/8” LESS than opening height.
See other side of page for cutting instructions.
Mount screw covers. 4
After door has been checked for proper operation and all
mounting screws have been tightened, engage short leg of
cover to barrel side of clip.
Tap cover onto outside clip with rubber
mallet so that long leg of cover sets
against frame of door surface.
DO NOT DAMAGE COVER.
A.
B.
ALL HOLE LOCATIONS ON HINGE LEAF MUST BE FASTENED TO
DOOR FOR PROPER OPERATION. FAILURE TO INSTALL ALL
FASTENERS WILL VOID WARRANTY AND UL FIRE LABEL LISTINGS.
!
CAUTION
Please follow the installation instructions carefully.
Not doing so may result in improper installation and
void the manufacturer’s guarantee.
INSTALLATION NOTES
No reinforcing is necessary except on heavy doors.
Reinforcement and rivet nuts are required in the frame and
door when door weight exceeds 300 pounds. Maximum
door weight is 600 pounds.
If the mullion is between the doors, treat as a single door
installation. If the mullion is behind the doors, treat as a
double door installation.
Reinforcing and Rivet Nuts:
Pairs of Doors with Mullions: