Marantz SR4001 User Manual
Page 40
36
ENGLISH
7.1 CH INPUT
The SR4001/SR5001 is equipped for future
expansion through the use of Multi channel SACD
multichannel player or DVD-Audio player.
When this is selected, the input signals connected to
the L(front left), R (front right), CENTER, SL (surround
left), SR (surround right) and SBL (surround back left)
and SBR (surround back right) channels of the 7.1
CH. In jacks are output directly to the front (left and
right), center, surround (left and right) and surround
back speaker systems as well as the pre-out jacks
without passing through the surround circuitry.
In addition, the signal input to the SW (subwoofer)
jack is output to the PRE OUT SW (subwoofer) jack.
When 7.1 CH. INPUT is selected, the last video input
used remains routed to the
Monitor Outputs
.
This permits simultaneous viewing with video
sources.
TAPE
CAT
P.SCAN
CAT
-
T.DISP
F.DIRECT
PTY
TUNING
PRESET
-
+
+
7
8
9
+10
REMOTE CONTROLLER
RC5001SR
0
0
HT-EQ
MULTI/
MENU
SPKR A/B
ENTER
EXIT
INFO
CH/
T.TONE
/SET UP
M-SPKR
MUTE
MD
CDR
CD
AMP
AUX2
TUNER
BASS
TREBLE
STEREO
NIGHT
M-CH ST
REC
AUDIO
ANGLE
SUB TITLE
DISC+
CH-SEL
V-OFF
ATT.
AUX1
A/D
MEMO
CL
DVD
DVD
VCR
VCR
DSS
DSS
TV
TV
VOLUME
VOLUME
7.1CH IN
7.1CH IN
2.
4.
1.
MULTI
SPEAKER
MULTI
PURE
SURROUND
STANDBY
PHONES
POWER ON/OFF
INPUT SELECTOR
AV SURROUND RECEIVER SR5001
DIRECT
AUTO
HT-EQ
MODE
1.
2.
DIGITAL
R
L
VIDEO
S-VIDEO
AUX 1 INPUT
AUDIO
T-MODE
MEMORY
ATT
MUTE
VOLUME
UP
DOWN
BAND
CLEAR
4.
RECORDING AN ANALOG SOURCE
In normal operation, the audio or video source
selected for listening through the SR4001/SR5001 is
sent to the record outputs.
This means that any program you are watching
or listening to may be recorded simply by placing
machines connected to the outputs for
TAPE OUT
,
CD-R/MD OUT, VCR1 OUT
in the record mode.
To record the input source signal you are currently
watching or listening to
TAPE
-
TUNING
PRESET
-
+
+
REMOTE CONTROLLER
RC5001SR
AMP
AUX2
BASS
TREBLE
AUDIO
ANGLE
SUB TITLE
DISC+
CH-SEL
V-OFF
ATT.
AUX1
MD
MD
CDR
CDR
CD
CD
DVD
DVD
VCR
VCR
TUNER
TUNER
DSS
DSS
TV
TV
1.
MULTI
SPEAKER
SETUP
SIMPLE
MULTI
PURE
SURROUND
STANDBY
PHONES
POWER ON/OFF
INPUT SELECTOR
AV SURROUND RECEIVER SR5001
DIRECT
AUTO
HT-EQ
MENU
MODE
1.
1.
Select the input source to record by turning the
INPUT SOURCE
knob on the front panel or
simply press the
input selector
buttons on the
remote.
The input source is now selected and you may
watch or listen to it as desired.
2.
The currently selected input source signal
is output to the
TAPE OUT, CD-R/MD OUT,
VCR1 OUT
outputs for recording.
3.
Start recording to the recording component as
desired.
Recording the video from one source and
the audio from another
You can add the sound from one source to the
video of another source to make your own video
recordings.
Below is an example of recording the sound from
a compact disc player connected to CD IN and the
video from a video camera connected to DSS/VCR2
to video cassette recorder connected to the VCR1
OUT jack.
TAPE
REMOTE CONTROLLER
RC5001SR
MD
CDR
DVD
AMP
AUX2
TUNER
DSS
TV
BASS
TREBLE
AUDIO
ANGLE
SUB TITLE
DISC+
CH-SEL
V-OFF
ATT.
AUX1
CD
CD
VCR
VCR
1.
2.
1.
Switch the video output source to VCR1 by
simply pressing the
input selector
buttons on
the remote.
2.
Switch the audio input source to CD by simply
pressing the
input selector
buttons on the
remote.
3.
Now “CD” has been selected as the audio input
source and “VCR1” as the video input source.
Notes:
• If you change the input source during recording, you
will record the signals from the newly selected input
source.
• You cannot record the surround effects.
• Digital input signals are only output to the digital
outputs. There is no conversion from digital to
analog.
When connecting CD players and other digital
components, do not connect only the digital
terminals, but the analog ones as well.
HT-EQ
MULTI
SPEAKER
DIGITAL
L
VIDEO
S-VIDEO
AUX 1 INPUT
SETUP
SIMPLE
MULTI
PURE
T-MODE
SURROUND
MEMORY
DISPLAY
MUTE
STANDBY
PHONES
POWER ON/OFF
INPUT SELECTOR
VOLUME
DOWN
AV SURROUND RECEIVER SR5001
DIRECT
AUTO
HT-EQ
EXIT
MENU
MODE
BAND
CLEAR
ENTER
Press the
HT-EQ
button on the front panel to turn on
the HT-EQ mode.
The tonal balance of a film soundtrack will be
excessively bright and harsh when played back over
audio equipment in the home. This is because fi lm
soundtracks were designed to be played back in
large movie theater environments.
Activating the HT-EQ feature when watching a fi lm
made for movie theaters corrects this and restores
the correct tonal balance.
The HT-EQ feature is available except in the following
modes.
• 7.1 CH INPUT
• PURE-DIRECT
• When VIRTUAL is set for the surround mode
SELECTING ANALOG AUDIO INPUT OR
DIGITAL AUDIO INPUT
TAPE
REMOTE CONTROLLER
RC5001SR
MD
CDR
CD
DVD
AUX2
VCR
TUNER
DSS
TV
AUX1
AMP
AMP
CAT
P.SCAN
CAT
4
5
6
7
8
9
0
+10
+10
HT-EQ
MULTI/
SPKR A/B
CH/
M-SPKR
MUTE
VOLUME
7.1CH IN
STEREO
NIGHT
M-CH ST
MEMO
CL
A/D
A/D
If you have already assigned the digital inputs, you
can temporarily select the audio input mode for each
input source as following procedures.
Press the
AMP
button and press the A/D (0) button.
When this button is pressed, the input mode is
switched in the following sequence.
→
HDMI Auto
→
HDMI
→
Digital Auto
→
Digital
→
Analog
→
HDMI Auto....
In HDMI Auto mode, the types of signals being input
to the digital and analog input jacks for the selected
input source are detected automatically.
If no digital signal is being input, the analog input
jacks are selected automatically.
In Digital and HDMI mode, input is fixed to an
assigned digital input terminal.
In analog mode, the analog input jacks are selected.
This selecting is temporary, so the result will not be
stored in memory.
If you need to change the input mode completely, use
INPUT SETUP in OSD menu system. (see page 25)