Marantz CC4001 - Manual (Page 6)

3
ENGLISH
BEFORE USING
NOTES FOR REMOVING
SHIPPING SCREWS
At the bottom of the player there are two red
shipping screws for use when the player is
transported. Before using the player, turn these
screws counterclockwise and remove them.
If the shipping screws are still in place and the
power is turned on, unplug the power cord from the
power outlet and remove the shipping screws.
Retain these screws as they will be needed when
the player is transported.
Before transporting the player, take out the discs,
close the disc tray, set to standby mode and
unplug the power cord from the power outlet. Then
install the shipping screws by turning them
clockwise. Be sure to fasten them securely.
INAPPROPRIATE PLACES
FOR INSTALLATION
To keep your player in perfect working order for the
longest possible time, avoid installing the player in
the following locations.
• Wherever it will be exposed to direct sunlight
• Wherever it will be close to a heater or other
heat-radiating appliance
• Wherever the humidity is high or ventilation is
poor
• Wherever it is very dusty
• Wherever it will be subject to vibration
• On top of a rickety stand or in an unstable
location which is tilted at an angle
• In an audio rack with little space at the top and
bottom or other location where the heat
dissipation will be obstructed
• To ensure proper heat dissipation, install the
player while leaving clearances between the
player and wall or other components, as shown
in the figure below.
• On top of an amplifier or other component
which dissipates a great deal of heat
* The quality of the laser and other components
can be harmed if the player is placed directly
on top of an amplifier or other device which
generates heat.
7 Do not place objects on top
• Refrain from placing any objects on top of the
player.
DISC R PROGRAM TRACK MP3 CD 1
6
11
16 2
7
12
17 3
8
13
18 4
9
14
19 5
10
15
20 RANDOM REPEAT 1DISC SEC MIN TOTAL
EACH
REMAIN 1 2 3 4 5
5 DISC CD CHANGER CC4001
POWER ON/STANDBY STANDBY
OPEN/CLOSE
REPEAT
LEVEL
PHONES
RANDOM
PLAY STOP PAUSE
DISC SKIP 1 2 3 4 5
NOTES ABOUT THE DISCS
* Handle the discs carefully so as not to
scratch their surfaces.
* Keep the surfaces of the discs clean at
all times.
When cleaning the surfaces of discs, always be
sure to use the special cleaner and wipe the
surfaces in the directions shown in the figure below.
* Do not attach pieces of paper or stickers
to the label surfaces of the discs.
When a disc has a piece of plastic tape or rental
CD label with paste protruding from the edge or
when a disc still bears traces of sticky tape or
adhesive labels, do not attempt to play it. If such
a disc is played on the CD player, you may find
that you cannot remove it or that some other kind
of malfunctioning may occur.
* Do not use discs which come in special
shapes.
Do not attempt to play heart-shaped or octagonal
discs or discs with any other special shapes.
You may find that you cannot remove them or
that some other kind of malfunctioning may occur
in the player.
* Use discs which satisfy the CD standards
such as those with the “CD logo” or
“
” mark on their disc label surfaces.
No guarantees are made for playback if discs
which do not satisfy the appropriate CD
standards are used.
Similarly, no guarantees are made for their sound
quality even if it is possible to play such discs.
* To protect your discs from damage, avoid
placing them in the following locations.
• Where they will be exposed to direct sunlight
or where they will be close to a heater or other
heat-radiating appliance
• Where the humidity level is high or it is very
dusty
• Near a window or other such location where
they may be exposed to rain
* Get into the habit of putting the discs
back in their cases after use.
• Wipe the surface
radially from the
center.
• Do not wipe the
surface in the
circumferential
direction.
shipping screws
4 ins. (0.1 m)
or more 4 ins. (0.1 m) or more
4 ins. (0.1 m) or more