Marantz SR4003 - Manual (Page 19)

15
ENGLISH
BASIC
CONNECTIONS
BASIC OPERA
TION
ADV
ANCED
CONNECTIONS
SETUP
ADV
ANCED
OPERA
TION
TROUBLESHOOTING
OTHERS
NAMES AND FUNCTIONS
BASIC OPERA
TION
BASIC OPERATION
AMP OPERATION
TURNING ON THE UNIT
1. Connect the AC power cord to the wall outlet.
2. Turn on the power of the audio equipment
connected to this unit. Set the input selector on
the audio equipment to this unit.
3. Press the POWER ON/OFF button on the unit.
Each time the button is pressed, the power of
the unit switches on/off.
Pressing POWER OFF or SOURCE ON/OFF
after pressing the AMP button on the remote
controller causes the STANDBY indicator on
the unit to light and puts the unit in STANDBY
mode.
To turn the power on while in STANDBY mode,
either press the ENTER button on the unit or
the AMP button on the remote controller, and
then press POWER ON or SOURCE ON/OFF.
SELECTING AN INPUT SOURCE
Before you can listen to any input media, you must
fi rst select the input source on the unit.
Example : DVD
DISP MULTI AUTO TUNED SLEEP SURR AUTO DIRECT
To select DVD, turn the INPUT SOURCE knob on
the front panel or simply press the DVD button on the
remote controller.
After you have selected DVD, simply turn on the DVD
player and play the DVD.
• As the input source is changed, the new input
name will appear momentarily an OSD information
on the video display. The input name will also
appear in the display, on the front-panel.
• As the input is changed, this unit will automatically
switch to the digital input, surround mode,
attenuation, and night mode status which were
entered during the confi guration process for that
source.
• When an audio source is selected, the last video
input used remains routed to the VCR Output
and Monitor Output. This permits simultaneous
viewing and listening to different sources.
• When a Video source is selected, the video
signal for that input will be routed to the Monitor
Output jacks and will be viewable on a TV monitor
connected to the unit.
If a component video input is connected to the
DVD or DSS component inputs, it will be routed
to the Component Video Output. Make certain
that your TV is set to the proper input to view the
signal.
ADJUSTING THE MAIN VOLUME
ANALOG DIGITAL DIGITAL SURROUND
AAC PCM L C R SL S SR LFE
Adjust the volume to a comfortable level using
the VOLUME control knob on the front panel or
VOLUME
3 / 4 buttons on the remote controller.
To increase the volume, turn the VOLUME knob
clockwise or press VOLUME
3 button on the
remote controller, to decrease the volume, turn
counterclockwise or press VOLUME
4 button on the
remote controller.
Notes:
• The volume can be adjusted within the range of – ∞
to 18 dB, in steps of 1 dB.
• However, when the channel level is set as described
on page 22, if the volume for any channel is set at +1
dB or greater, the volume cannot be adjusted up to 18
dB.
(In this case the maximum volume adjustment range is
“18 dB - Maximum value of channel level)
ADJUSTING THE TONE (BASS & TREBLE) CONTROL
During a listening session you may wish to adjust the
Bass and Treble Control to suit your listening tastes
or room acoustics.
(Using the remote controller)
To adjust the bass effect, press BASS + or BASS
– on the remote controller.
To adjust the treble effect, press TREBLE + or
TREBLE – on the remote controller.
Note:
The tone control function can work in the AUTO
Surround, Stereo, Dolby PLIIx, DTS, DTS-ES, and
Multi Ch. Stereo mode.
TEMPORARILY TURNING OFF THE SOUND
To temporarily silence all speaker outputs such as
when interrupted by a phone call, press the MUTE
button on the remote controller.
This will interrupt the output to all speakers and the
head-phone jack, but it will not affect any recording or
dubbing that may be in progress.
When the system is muted, the display will show
“MUTE” .
Press the MUTE button again to return to normal
operation.