Memorex MVR4042 - Manual (Page 18)

18
RECORDING AND VIEWING THE
SAME TV PROGRAM
CHECK BEFORE YOU BEGIN
• Turn ON the TV and set to the video channel 3 or 4.
• Turn ON the VCR POWER button.
• Press the TV/VCR selector button to select the
VCR mode.
When a TV is connected with an audio/video cable, turn
the TV and this VCR on and select the video input mode
on the TV.
1 Load a cassette tape with the
erase prevention tab intact.
The VCR will automatically
turn on.
TO WATCH A TAPE REPEATEDLY
NOTE: To cancel repeat mode, follow the above steps
1 and 2, then press the ENTER button to select
the OFF position. Press the MENU button to
return to the TV.
CHECK BEFORE YOU BEGIN
• Turn ON the TV and set to the video channel 3 or 4.
• Turn ON the VCR POWER button.
• Press the TV/VCR selector button to select the VCR
mode.
When a TV is connected with an audio/video cable,
turn the TV and this VCR on, and select the video input
mode on the TV.
SLOW MOTION PLAYBACK
Press the SLOW button in the PLAYBACK mode.
Playback will proceed at 1/10th of the normal speed.
Press the PLAY button again to resume normal playback.
NOTE: SLOW TRACKING AND VERTICAL LOCK
ADJUSTMENT
If noise bars appear in the picture during slow motion,
press the TRACKING SET + or – button to reduce the
noise bars.
If the still picture jitters excessively, press the
TRACKING SET + or – button to stabilize the still
picture.
" " will appear if you press the CALL button.
To cancel, press the CALL button again.
1 Press the MENU button.
Press the TRACKING SET +
or – button to select the AUTO
REPEAT option.
2 Press the ENTER button to
select the ON position.
3 Press the MENU button.
If you press the PLAY button, the
tape will play over and over until
the repeat mode is canceled.
SPECIAL PLAYBACK
TO VISUALLY SEARCH FOR
DESIRED POINTS
When either the F.FWD or REW button is pressed in the
PLAYBACK mode, the speed search picture will appear.
When pressed twice, the search picture will increase
speed. Speed search time depends upon the speed
used (SP, LP or SLP) during recording.
FRAME BY FRAME ADVANCE
Press the PAUSE/STILL button in the PLAYBACK mode.
Press the PAUSE/STILL button again to resume normal
playback.
Press the SLOW button during STILL playback.
The still picture will advance by one frame each time
you press the button. Hold the button for continuous
frame by frame viewing.
Press the PAUSE/STILL button again to resume normal
playback.
NOTES: • A few noise bars will appear on the picture
during SPEED SEARCH and STILL.
• The audio output is muted during SPEED
SEARCH, STILL, FRAME ADVANCE and
SLOW MOTION.
• To prevent damage to the tape, special
playback is automatically changed to the
PLAYBACK mode after 5 minutes.
RECORDING A TV
PROGRAM
TO WATCH A STILL PICTURE
á+/-/ENTER/MENUñ
MENU
TIMER REC SET
AUTO REPEAT ON OFF
ON OFF SAP
CH SETUP
SYSTEM SETUP
á+/-/ENTER/MENUñ
MENU
TIMER REC SET
AUTO REPEAT ON OFF
ON OFF SAP
CH SETUP
SYSTEM SETUP
TAPE SPEED AND
RECORDING/PLAYBACK TIME
You can select the two different tape speeds before
recording.
This VCR selects the playback tape speed SP,
LP(Long Play) or SLP automatically.
TAPE SPEED
VIDEO CASSETTE TAPE
T120
SP
Standard Play
SLP
Super Long Play
2 hours
6 hours
2-2/3 hours
8 hours
T160
4F90701A/E P14-19 20/03/2003, 10:32 18