Pci expansion connector, Power requirements, Board size – Motorola MVME5100 Series User Manual
Page 4: Ipmc modules, Pmc interface, Scsi bus, Synchronous serial ports, Asynchronous serial ports, Parallel port, Transition modules
PCI Expansion Connector
Power Requirements
(not including power required by PMC or IMPC modules)
Board Size
I P M C M o d u l e s
PMC Interface
SCSI Bus
Synchronous Serial Ports
Asynchronous Serial Ports
Parallel Port
Power Requirements
(additional power load placed on MVME5100 with IPMC installed)
T r a n s i t i o n M o d u l e s
I/O Connectors
Board Size
A l l M o d u l e s
Environmental
(Minimum of 400 LFM (linear feet per minute) of forced air cooling is
recommended for operation in the higher temperature ranges.)
Address/Data:
A32/D32/D64
PCI Bus Clock:
33 MHz
Signaling:
5V
Connector:
114-pin connector located on the planar
of the MVME5100
+5V
±
5%
+12V
±
10%
–12V
±
10%
MVME5100:
3.0 A typ.
8.0 mA typ.
2.0 mA typ.
MVME5100 with
MVME761:
3.2 A typ.,
4.0 A max.
0.2 A typ.
0.5 A max.
0.1 A typ.
0.3 A max.
Height:
233.4 mm (9.2 in.)
Depth:
160.0 mm (6.3 in.)
Front Panel Height:
261.8 mm (10.3 in.)
Width:
19.8 mm (0.8 in.)
Max. Component
Height:
14.8 mm (0.58 in.)
Address/Data:
A32/D32/D64, PMC PN1, PN2, PN3,
PN4 connectors
PCI Bus Clock:
33 MHz
Signaling:
5V
Module Type:
Basic, single-wide; P2 I/O
Controller:
Symbios 53C895A
PCI Local Bus DMA:
Yes, with PCI local bus burst
Asynchronous (8-bit
mode):
5.0MB/s
Ultra SCSI:
20.0MB/s (8-bit mode), 40.0MB/s (16-bit
mode)
Note: 16-bit SCSI operation precludes the use of some PMC Slot 2
signals.
Controller:
85230/8536
Number of Ports:
Two (IPMC761); one (IPMC712)
Configuration:
IPMC761: TTL to P2 (both ports), SIM
configurable on MVME761;
IPMC712: EIA-232 to P2
Baud Rate, bps max.:
2.5M sync, 38.4K async
Oscillator Clock Rate
(PCLK):
10 MHz/5 MHz
Controller:
16C550 UART; 85230/8536
Number of Ports:
Two (IPMC761); three (IPMC712)
Configuration:
EIA-574 DTE (IPMC761);
EIA-232 (IPMC712)
Async Baud Rate, bps
max.:
38.4K EIA-232, 115Kbps raw
Controller:
PC97307
Configuration:
8-bit bi-directional, full IEEE 1284 sup-
port; Centronics compatible (minus EPP
and ECP on MVME712M)
Modes:
Master only
IPMC761
IPMC712
+5V:
0.5 A max.
0.5 A max.
+3.3V
0.75 A max.
0.75 A max.
MVME761
MVME712M
Asynchronous
Serial Ports:
Two, DB-9 labeled as
COM1 and COM2
Three, DB-25 labeled
as Serial 1, Serial 2,
and Serial 3
Synchronous
Serial Ports:
Two HD-26 labeled as
Serial 3 and Serial 4
(user configurable via
installation of SIMs),
Two 60-pin connectors
on MVME761 planar
for installation of two
SIMs
One, DB-25 labeled as
Serial 4
Parallel Port:
HD-36, Centronics
compatible
D-36, Centronics com-
patible
Ethernet:
10BaseT or
100BaseTX, RJ-45
not available
SCSI:
8- or 16-bit, 50- or 68-
pin connector via P2
adapter
8-bit, standard SCSI D-
50
Height:
233.4 mm (9.2 in.)
Depth:
80.0 mm (3.1 in.)
Front Panel Height:
261.8 mm (10.3 in.)
Front Panel Width:
MVME761: 19.8 mm (0.8 in.)
MVME712M: 39.6 mm (1.6 in.)
Operating
Nonoperating
Temperature:
0° C to +55° C
(inlet air temp. w/forced
air cooling)
–40° C to +85° C
Humidity (NC):
5% to 90%
5% to 90%
Vibration:
2 Gs RMS,
20–2000 Hz random
6 Gs RMS,
20–2000 Hz random