A/v receiver or stereo system, Satellite receiver or other device with s-video, Important – MITSUBISHI ELECTRIC WS-48515 User Manual
Page 19: Figure 7. connecting an a/v receiver, Ieee1394
18
19
For digital audio connections, see your
A/V Receiver, DVD and Satellite Receiver
Owner’s Guides.
IMPORTANT
A/V Receiver or Stereo System
Figure 7
A digital audio cable and stereo audio cables are required. The
digital audio cable is provided. The stereo audio cables are not
included with the TV.
1. Connect a set of stereo audio cables from OUTPUT
AUDIO 2 on the TV back panel to the TV AUDIO
INPUT on the back of the A/V Receiver. The red
cable connects to the R (right) channel and the
white cable connects to the L (left) channel.
To connect a digital A/V Receiver with Dolby®
Digital surround sound:
2. Connect one end of the digital audio cable supplied
with the TV to DIGITAL AUDIO on the back of the
TV. Connect the other end to the COAXIAL DIGITAL
INPUT on the back of the A/V Receiver.
Check A/V Receiver’s Owner’s Guide for information
concerning the use of the digital input and switching
between the digital sound and analog stereo sound
from the TV.
SERVICE WARNING
X-RAY PRECAUTION:
THIS PRODUCT
I N C L U D E S C R I T I C A L ME C H A N I C A L
AND E LECTRICAL PARTS WHICH ARE
ESSENTIAL FOR X-RADIATION SAFETY.
F O R CO NT I NUE D S A F E T Y R E P LA CE
CR I T I CA L C O MP O NE NT S I ND I CAT E D
IN THE SERVICE MANUAL ONLY WITH
E X ACT R E PLACE ME NT PART S GIV E N
IN THE PARTS LIST. REFER TO SERVICE
MANUAL FOR OPERATING HIGH VOLTAGE AT
MINIMUM BRIGHTNESS, MEASUREMENT
PROCE DURE S AND PROPER SERV ICE
ADJUSTMENTS.
WARNING:
HANDLE WITH CARE. HIGH
VACUUM PICTURE TUBE IS DANGEROUS
TO HANDLE.
REFER SERVICING TO
Q UA LI F I E D S E R V I CE PE R S O NNE L.
REPLACE WITH A TUBE OF THE SAME
TYPE NUMBER FOR CONTINUED SAFETY.
CAUTION:
TO MEASURE SECOND
ANODE VOLTAGE USE A HIGH VOLTAGE
METER CONNECTED FROM ANODE LEAD
TO CHASSIS ONLY. DISCHARGE HIGH
VOLTAGE TO CHASSIS ONLY, NOT TO
EXTERNAL GROUND.
IR EMITTER
NetCommand
R
DIGITAL
SERVICE
PORT
IEEE1394
INPUT/OUTPUT
AUDIO
ANT-2
AUX
ANT-1
MAIN
CableCARD
TM
SLOT
–
(DTV/CABLE /VHF/UHF)
–
S-VIDEO
VIDEO
INPUT
1
2
AUDIO-
LEFT/
(MONO)
AUDIO-
RIGHT
COMPONENT
YPbPr (480i/480p/1080i)
2
1
Y
Pb
Pr
AUDIO-
LEFT/
(MONO)
AUDIO-
RIGHT
DVI
Digital Video
Digital Audio
Analog Audio
IN
IN
IN
IN
IN
IN
IN
IN
OUT
OUT
OUT
OUT
AUX
CD
TAPE 1
TAPE 2
VCR 1
VCR 2
TV
DVD
MONITOR
VCR 1
VCR 2
TV
DVD
MONITOR
VCR 1
VCR 2
TV
DVD
OUT
OUT
IN
IN
IN
IN
IN
IN
IN
IN
OUT
OUT
OUT
OUT
CENTER
SUB
WOOFER
FRONT
SUR.
REC
SOURCE
LINE OUT
PRE OUT
SURROUND
SPEAKERS
���� MIN.�
FRONT
SPEAKERS-A
���� MIN.�
FRONT
SPEAKERS-B
���� MIN.�
CENTER
��� MIN.�
L
L
L
L
L
R
R
R
R
THIS DEVICE COMPLIES WITH PART 15 OF THE
FCC RULES. OPERATION IS SUBJECT TO THE
FOLLOWING TWO CONDITIONS: (1) THIS DEVICE
MAY NOT CAUSE HARMFUL INTERFERENCE AND
(2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE
RECEIVED, INCLUDING INTERFERENCE THAT MAY
CAUSE UNDESIRED OPERATION.
MANUFACTURED UNDER LICENSE FROM DOLBY LABORATORIES LICENSING
CORPORATION. "DOLBY", "PRO LOGIC" AND THE DOUBLE-D SYMBOL ARE
TRADEMARKS OF DOLBY LABORATORIES CORPORATION.
COPYRIGHT 1992 DOLBY LABORATORIES, INC. ALL RIGHTS
RESERVED
INPUT-1
(OPTICAL)
INPUT-2
(COAXIAL)
INPUT-3
(COAXIAL)
DIGITAL AUDIO
SWITCHED
UNSWITCHED
AC 120V - 60Hz
TOTAL 100W, 0.9A MAX
AC OUTLETS
MITSUBISHI
AUDIO/VIDEO RECEIVER
MODEL
M-VR1000
POWER SUPPLY
POWER CONSUMPTION
120V-60Hz
552W, 732VA
DISTRIBUTED BY
MITSUBISHI CONSUMER ELECTRONICS AMERICA
INC.
6100 ATLANTIC BLVD
MADE IN
JAPAN
NORCROSS, GA 30071-1305
FABRIQUE EN
JAPAN
!
AVIS
RISQUE DE CHOC ELECTRONQUE
NE PAS ENLEVER
RISK OF ELECTRIC SHOCK
DO NOT OPEN
ANTENNA
75
�
300
�
FM
AM
GND
ATUO
STANDBY
ON
OFF
�
�
S-VIDEO
VIDEO
AUDIO
WARNING
A/V Receiver Rear Panel
Use only if
connecting
a Dolby Digital
A/V Receiver
DIGITAL
AUDIO
AUDIO-
LEFT/
(MONO)
AUDIO-
RIGHT
MONITOR OUTPUT
AUDIO 2
2.
2.
1.
Red
White
Red
White
1.
TV back panel
AUDIO/VIDEO 1
Figure 7. Connecting an A/V Receiver
Connecting an A/V Receiver or Stereo System or
a Satellite Receiver or Other Device with S-Video
Satellite Receiver or Other Device with
S-Video
Figure 8
An S-Video cable and audio cables are required. These are not
included with the TV.
1. Connect an S-Video cable from VIDEO OUT on the
satellite receiver back panel to INPUT-2 VIDEO on
the TV back panel.
2. Connect a set of audio cables from AUDIO OUT on
the satellite receiver back panel to INPUT-2 AUDIO,
on the TV back panel. The red cable connects to
the R (right) channel and the white cable connects to
the L (left) channel.
Note: Refer to the Satellite Receiver Owner’s
Guide for Dish Antenna connections.
SERVICE WARNING
X-RAY PRECAUTION:
THIS PRODUCT
I N C L U D E S C R I T I C A L ME C H A N I C A L
AND E LECTRICAL PARTS WHICH ARE
ESSENTIAL FOR X-RADIATION SAFETY.
F O R CO NT I NUE D S A F E T Y R E P LA CE
CR I T I CA L C O MP O NE NT S I ND I CAT E D
IN THE SERVICE MANUAL ONLY WITH
E X ACT R E PLACE ME NT PART S GIV E N
IN THE PARTS LIST. REFER TO SERVICE
MANUAL FOR OPERATING HIGH VOLTAGE AT
MINIMUM BRIGHTNESS, MEASUREMENT
PROCE DURE S AND PROPER SERV ICE
ADJUSTMENTS.
WARNING:
HANDLE WITH CARE. HIGH
VACUUM PICTURE TUBE IS DANGEROUS
TO HANDLE.
REFER SERVICING TO
Q UA LI F I E D S E R V I CE PE R S O NNE L.
REPLACE WITH A TUBE OF THE SAME
TYPE NUMBER FOR CONTINUED SAFETY.
CAUTION:
TO MEASURE SECOND
ANODE VOLTAGE USE A HIGH VOLTAGE
METER CONNECTED FROM ANODE LEAD
TO CHASSIS ONLY. DISCHARGE HIGH
VOLTAGE TO CHASSIS ONLY, NOT TO
EXTERNAL GROUND.
IR EMITTER
NetCommand
R
DIGITAL
SERVICE
PORT
IEEE1394
INPUT/OUTPUT
AUDIO
ANT-2
AUX
ANT-1
MAIN
CableCARD
TM SLOT
–
(DTV/CABLE /VHF/UHF) –
S-VIDEO
VIDEO
INPUT
1
2
AUDIO-
LEFT/
(MONO)
AUDIO-
RIGHT
COMPONENT
YPbPr (480i/480p/1080i)
2
1
Y
Pb
Pr
AUDIO-
LEFT/
(MONO)
AUDIO-
RIGHT
DVI
Digital Video
Digital Audio
Analog Audio
AUDIO-
LEFT/
(MONO)
AUDIO-
RIGHT
MONITOR OUTPUT
AUDIO 2
TV back panel
AUDIO/VIDEO 1
(Y/C)
L
R
L
R
1
2
VIDEO OUT
AUDIO OUT
AUDIO IN
Any S-Video Device
White
Red
1.
White
Red
1.
2.
2.
INPUT
1
2
Note: NetCommand® will asssume you
connected your Satellite Receiver to Input-2.
If you add a second Satellite Receiver or use
any other inputs for your Satellite Receiver,
this change must match in the NetCommand
system. See Edit NetCommand... pages 35-42
for more information.
Figure 8. Connecting a Satellite Receiver with S-Video