beautypg.com

Reparation, Initial setup, Before you begin – Philips Magnavox 42MF439B User Manual

Page 14: After an initial setup is completed, Autoprogram” will begin

background image

14

EN

P

REPARATION

Initial Setup

This section will guide you through the unit’s initial setting which includes
selecting a language for your on-screen menu and autoprogram, which
automatically scans and memorizes viewable channels.

Before you begin:

Make sure the unit is connected to antenna or cables.

1

After making all the necessary connections,
press [y

y

(power)] to turn on the unit.

This operation may take a few moments.

2

Use [Cursor K / L] to select the on-screen language
from the choices on the right side of the TV screen.
(English / Español / Français)

t

Initial Setup

Select the language for setup display.

El ja el idioma de ajuste.

Sélectionner langue écran config.

Español

Français

Se ect

Skip

MENU

OK

OK

Engl sh

“Initial Setup” menu on step 3 will be displayed in the
selected language after you press [OK].

3

Use [Cursor K / L] to select “Antenna” for TV channels
or “Cable” for CATV channels, then press [OK].

Initial Setup

Initial Setup

Se ect

Sk p

ME

B K

Back

OK

OK

Make sure the antenna is connected to ''ANT. IN ' jack.
Select your signal source.

Cab e

Skip

Antenna

Cab e

Antenna

Or

ANT IN

“Autoprogram” will begin.

t

Initial Setup

Now the system is scanning for channels, please wait.
Auto programming wi l take up to 20 minutes to complete.

Sk p

MENU

0%

Analog channels

0ch

Dig tal channels

0ch

5

4

Use [Cursor s / B] to select the desired location setting,
then press [OK].

S

Initial Setup

Select “Retail” or “Home” for your location.

OK

OK

Retail

H o m e

Select

Select ”Retail”, the unit will be set up with predefined
setting for retail displays.
Select ”Home”, the unit is set to maximize the energy
efficiency for home setting and it can be adjusted
through a choice of picture and sound quality
according to your preference.
When the initial setup is completed, the lowest
memorized channel with the confirmation message
of the location setting will be displayed on the TV
screen.

Note:

• If you connect the cable system directly, contact the CATV

installer.

• If you press [y

y

(power)] or [MENU] during autoprogram,

this setting will be canceled.

• The initial autoprogram function can be executed for

either “Antenna” or “Cable” only once. When you change
the connection (Antenna / Cable), set autoprogram again.
(Refer to page 19.)

• If there is no signal input from the antenna terminal and

no operation for several seconds after you turn on the unit,
“Helpful Hints” appears. Follow the instructions listed on
the TV screen.

t

Initial Setup

Select

Skip

MENU

No channel is registered.
Try Autoprogram again?
Ver fy that you have a cable connected to the "ANT. IN" jack on the
back panel of the TV, he cannel installa ion process searches this
connection. f you are using a cable or sate l te box please con irm
the input to which you have connected the box and use "SOURCE"
key on the remote control to tune to he appropriate source input.

La er

Retry

OK

OK

• You must set ”Home” in step 4. Otherwise, the settings

of picture and sound quality you adjusted will not be
memorized after you turn off the unit.

After an initial setup is completed...

If you want to scan the channels automatically again,
refer to “Autoprogram” on page 19.

You can add the desired channels unmemorized by
“Autoprogram”. Refer to “Add Channels” on page 20.

If you want to change to another language, refer to
“Language Selection” on page 21.

If you want to change the location setting, refer to
“Location” on page 32.

These operations are accessible by remote control. Some may also be accessible by controls on the main unit.