beautypg.com

Milwaukee 5446-21 User Manual

Page 2

background image

2

3

PERSONAL SAFETY

GENERAL POWER TOOL SAFETY WARNINGS

WORK AREA SAFETY

ELECTRICAL SAFETY

• Keep work area clean and well lit. Cluttered or

dark areas invite accidents.

• Do not operate power tools in explosive atmo-

spheres, such as in the presence of fl ammable
liquids, gases or dust.
Power tools create
sparks which may ignite the dust or fumes.

• Keep children and bystanders away while

operating a power tool. Distractions can cause
you to lose control.

• Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools.
Unmodifi ed plugs and matching outlets will
reduce risk of electric shock.

• Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and
refrigerators.
There is an increased risk of elec-
tric shock if your body is earthed or grounded.

• Do not expose power tools to rain or wet con-

ditions. Water entering a power tool will increase
the risk of electric shock.

• Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges
or moving parts.
Damaged or entangled cords
increase the risk of electric shock.

• When operating a power tool outdoors, use

an extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use reduces
the risk of electric shock.

• If operating a power tool in a damp location

is unavoidable, use a residual current device
(RCD) protected supply.
Use of an RCD reduces
the risk of electric shock.

medication. A moment of inattention while oper-
ating power tools may result in serious personal
injury.

• Use personal protective equipment. Always

wear eye protection. Protective equipment such
as dust mask, non-skid safety shoes, hard hat, or
hearing protection used for appropriate conditions
will reduce personal injuries.

• Prevent unintentional starting. Ensure the

switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool.
Carrying power tools
with your fi nger on the switch or energising power
tools that have the switch on invites accidents.

• Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key
left attached to a rotating part of the power tool
may result in personal injury.

• Do not overreach. Keep proper footing and

balance at all times. This enables better control
of the power tool in unexpected situations.

• Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing and gloves
away from moving parts.
Loose clothes, jewel-
lery or long hair can be caught in moving parts.

• If devices are provided for the connection of

dust extraction and collection facilities, en-
sure these are connected and properly used.
Use of these devices can reduce dust-related
hazards.

WARNING

READ ALL SAFETY WARNINGS AND INSTRUCTIONS.

Failure to follow the warnings and instructions may result in electric shock, fi re and/or
serious injury.

Save all warnings and instructions for future reference

The term "power tool" in all of the warnings refers to your mains-operated (corded) power
tool or battery-operated (cordless) power tool.

POWER TOOL USE AND CARE

• Do not force the power tool. Use the correct

power tool for your application. The correct
power tool will do the job better and safer at the
rate for which it was designed.

• Do not use the power tool if the switch does

not turn it on and off. Any power tool that cannot
be controlled with the switch is dangerous and
must be repaired.

• Disconnect the plug from the power source

and/or the battery pack from the power tool
before making any adjustments, changing

accessories, or storing power tools. Such
preventive safety measures reduce the risk of
starting the power tool accidentally.

• Store idle power tools out of the reach of chil-

dren and do not allow persons unfamiliar with
the power tool or these instructions to operate
the power tool.
Power tools are dangerous in the
hands of untrained users.

• Maintain power tools. Check for misalignment

or binding of moving parts, breakage of parts
and any other condition that may affect the
power tool operation. If damaged, have the
power tool repaired before use.
Many accidents
are caused by poorly maintained power tools.

• Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.

• Use the power tool, accessories and tool bits

etc., in accordance with these instructions,
taking into account the working conditions
and the work to be performed.
Use of the power
tool for operations different from those intended
could result in a hazardous situation.

SERVICE

• Have your power tool serviced by a qualifi ed

repair person using only identical replacement
parts.
This will ensure that the safety of the power
tool is maintained.

SPECIFIC SAFETY RULES

• Stay alert, watch what you are doing and use

common sense when operating a power tool.
Do not use a power tool while you are tired
or under the infl uence of drugs, alcohol or

• Wear ear protectors. Exposure to noise can

cause hearing loss.

• Use auxiliary handles supplied with the tool.

Loss of control can cause personal injury.

• Hold power tools by insulated gripping sur-

faces when performing an operation where
the cutting tool may contact hidden wiring or
its own cord.
Contact with a “live” wire will make
exposed metal parts of the tool “live” and shock
the operator.

• Keep hands away from all cutting edges and

moving parts.

• Maintain labels and nameplates. These carry

important information. If unreadable or missing,
contact a MILWAUKEE service facility for a free
replacement.

• WARNING: Some dust created by power sand-

ing, sawing, grinding, drilling, and other construc-
tion activities contains chemicals known to cause
cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:

• lead from lead-based paint

• crystalline silica from bricks and cement and other

masonry products, and

• arsenic and chromium from chemically-treated

lumber.

Your risk from these exposures varies, depend-

ing on how often you do this type of work. To
reduce your exposure to these chemicals: work
in a well ventilated area, and work with approved
safety equipment, such as those dust masks that
are specially designed to fi lter out microscopic
particles.

BPM

Blows per Minute (BPM)

Volts Alternating Current

Amps

No Load Revolutions per
Minute (RPM)

Underwriters Laboratories, Inc.,
United States and Canada

Mexican Approvals Marking

Symbology

Specifi cations

No Load

RPM

350 / 450

- -

No Load

Blows per

Minute

2200 / 2840

2200 / 2840

Cat.

No.

5426-21

5446-21

Carbide Tipped

Percussion Bit

(concrete)

1-3/4"

- -

Tool

Capacities

Volts

AC

120

120

Amps

14

14

Percussion

Core Bit

(concrete/brick)

4-1/2" / 6"

- -

Shank

Type

SDS-Max

SDS-Max

This manual is related to the following products: