MITSUBISHI ELECTRIC WD-Y57 a - Manual (Page 25)

Chapter 2. TV Connections 25
VCR to a Cable Box (Audio & Video)
Required: Two-way RF splitter, 4 coaxial cables, right and
left audio cables, S-Video or composite video cable, plus
component or S-Video cables and audio cables required
to connect the TV to the cable box.
1. Connect the incoming cable to IN on the RF splitter.
2. Connect one coaxial cable from OUT on the RF split-
ter to CABLE IN on the cable box.
3. Connect one coaxial cable from OUT on the RF
splitter to ANT 1/MAIN on the TV back panel. This
connection also allows you to use the TV Guide On
Screen® and Split Screen features.
4. Connect one coaxial cable from OUT on the cable
box to ANTENNA IN on the VCR back panel.
5. Connect the cable box outputs to the TV as shown
in one of the options listed below. This connection
allows the TV to receive the best available signal
directly from the cable box.
Figure 1: Component video output to the TV’s
COMPONENT Y Pb Pr jacks; analog stereo
audio to the associated
AUDIO jacks.
OR
Figure 2: S-Video output to the TV’s
INPUT/S-VIDEO jack; analog stereo audio to
the associated
AUDIO jacks.
Figure 7. Connecting a VCR to a cable box
"/5&//"
065 065
065
065
*/ */
*/
*/
3
-
"6%*0
7*%&0 47*%&0
"/5&//"
065 065
065
065
*/
*/
*/
3
- -
"6%*0
7*%&0 47*%&0
3
$"#-&
065 */
:
1C
1S
3
-
"6%*0
47*%&0
$"#-&
065 */
:
1C
1S
3
-
"6%*0
47*%&0
1$%7*
"6%*0
"6%*0
065
$0.10/&/5
*/165
.0/*503
065
)%.*%7*"6%*0
"/5."*/ "/5"69
*&&& %*(*5"-
"6%*0
065
)%.*
1$%7*
7*%&0
-&'5
3*()5
-&'5
3*()5
:
1C
1S
"6%*0
-&'5
.0/0
"6%*0
3*()5
-&'5
3*()5
64&8*5) $BCMF$"3%™
$BCMF$"3%™ 64&8*5) "/5$"3%501
47*%&0
7*%&0
"6%*0
-&'5
.0/0
"6%*0
3*()5
)%.*$0.1"5*#*-*5:
7*%&0JQQJQ
$0.10/&/5$0.1"5*#*-*5:
7*%&0JQQJ
%7**1$$0.1"5*#*-*5:
3&'&35008/&34(6*%&
TM
R
"/5."*/ 64&8*5) $BCMF$"3%™
*/
065
065
5808
" :41-*55&3
6. To use the TV speakers with the VCR, connect left
(white) and right (red) audio cables from AUDIO OUT
on the VCR back panel to INPUT/AUDIO LEFT
and AUDIO RIGHT on the TV back panel. If your
VCR is mono (non-stereo), connect only the white (left)
cable.
7. Connect either an S-Video or composite video
cable from VIDEO OUT on the VCR back panel to
INPUT/VIDEO or INPUT/S-VIDEO on the TV
back panel. Connect only one type of video cable.
S-Video is recommended, if available.
Optional
8. To allow recording from the TV to the VCR:
a. Connect left (white) and right (red) audio cables
from AUDIO IN on the VCR back panel to
MONITOR OUT/LEFT and RIGHT on the TV
back panel.
b. Connect a video cable from VIDEO IN on the
VCR back panel to MONITOR OUT/VIDEO on
the TV back panel.
Note: When using this connection configuration with the
connections used in step 5, it is possible to view
live cable programs through the VCR Device. For
best picture quality always view live cable pro-
grams directly from the cable box device.