Blw-400ssw — pre-setup, Caution – Multiquip MQ Power Duelweld Welder/Ac Generator BLW-400SSW User Manual
Page 29
BLW-400SSW-WELDER/AC GENERATOR— PARTS & OPERATION MANUAL— REV. #1 (06/15/01) — PAGE 29
BLW-400SSW — PRE-SETUP
Operation in Freezing Weather
When operating in freezing weather, be certain that the proper
amount of antifreeze has been added. See Table 10 for
antifreeze operating temperatures.
Day-to-day addition of coolant or antifreeze is done from the
reserve tank. See Table 9 for engine, radiator and reserve
tank coolant capacities. Make sure the coolant level in the
reserve tank is always between the "H" and the "L" markings.
Cleaning the Radiator
The radiator may overheat if the fins become overloaded
with dust or debris. Periodically clean the radiator fins with
compressed air.
Fan Belt Tension
A slack fan belt may contribute to overheating, or to
insufficient charging of the battery. Inspect and adjust it in
accordance with the
Kubota Engine Operator's Manual.
The fan belt tension is proper if the fan belt (Figure 5) bends
7 to 9 mm (0.28- to 0.35 in.) when depressed with the thumb
as shown in Figure 13 below.
CAUTION :
When adding coolant or antifreeze to the
radiator, do not remove the radiator cap
until the unit has completely cooled.
When the antifreeze is mixed with
water, the antifreeze mixing ratio must
be less than 50%.
NOTE
Air Cleaner
Periodic cleaning/replacement is necessary. Inspect it in
accordance with the
Kobota Engine Operator's Manual.
Battery
This unit is of negative ground. DO NOT connect in reverse.
Always maintain battery fluid level between the specified
marks. Battery life will be shortened, if the fluid level is not
properly maintained. Add only distilled water when
replenishment is necessary.
The battery is sufficiently charged if the specific gravity of
the battery fluid is 1.28 (at 68° F). If the specific gravity
should fall to 1.245 or lower, it indicates that the battery is
dead and needs to be recharged or replaced.
Check to see whether the battery cables are loose. Poor
contact may result in poor starting or malfunctions, always
keep the terminals firmly tightened. Coating the terminals
with a thin film of grease will help to inhibit corrosion.
Figure 13. Fan Belt Tension
s
e
r
u
t
a
r
e
p
m
e
T
g
n
it
a
r
e
p
O
e
z
e
e
r
F
-i
t
n
A
.
0
1
e
l
b
a
T
%
l
o
V
e
z
e
e
r
F
-i
t
n
A
t
n
i
o
P
g
n
i
z
e
e
r
F
t
n
i
o
P
g
n
il
i
o
B
C
°
F
°
C
°
F
°
0
4
4
2
-
2
1
-
6
0
1
2
2
2
0
5
7
3
-
4
3
-
8
0
1
6
2
2
y
ti
c
a
p
a
C
t
n
a
l
o
o
C
.
9
e
l
b
a
T
r
o
t
a
i
d
a
R
d
n
a
e
n
i
g
n
E
)
L
6
1
.
4
(
.l
a
G
1
.
1
k
n
a
T
e
v
r
e
s
e
R
)
L
5
7
.
0
(
.l
a
G
2
.
0
CAUTION
:
Never place hands near the belts or fan
while the welder/AC generator is running.
Table of Contents