Inventory – Grizzly G0656 User Manual
Page 13
G0656 8" Jointer with Built-In Mobile Base
-11-
Inventory
The following is a description of the main compo-
nents shipped with your machine. Lay the compo-
nents out to inventory them.
Note: If you can't find an item on this list, check
the mounting location on the machine or examine
the packaging materials carefully. Occasionally
we pre-install certain components for shipping
purposes.
Wood Crate: (Figure 3)
Qty
A. Jointer Assembly ........................................ 1
B. Cutterhead Guard ....................................... 1
C. Handwheels ................................................ 2
D. Handles ...................................................... 2
E. Fence Tilt Lever ......................................... 1
F. Push Blocks ................................................ 2
G. Knife Setting Gauge Hardware Bag
— Knife Setting Gauge Rod ........................ 1
— Knife Setting Gauge Foot ....................... 2
— E-Clip 8mm ............................................. 2
H. Tool Hardware Bag
— Hex Wrenches 2.5, 3, 4, 6mm ......1 Each
—Open-end Wrench 8/10, 12/14mm ......... 1
Cardboard Box: (Figure 4)
Qty
I. Stand Assembly w/Motor and Door ........... 1
J. Pedestal Switch .......................................... 1
K. Wheel Assembly ......................................... 1
L. V-Belt .......................................................... 1
M. Dust Port ................................................... 1
Assembly Fasteners
Qty
•
Hex Bolt M8-1.25 x 50 (Wheel/Stand) ....... 1
•
Flat Washer 8mm (Wheel/Stand) ............... 1
•
Hex Bolts M10-1.5 x 55 (Wheel/Stand) ...... 2
•
Flat Washers 10mm (Wheel/Stand) ........... 2
•
Hex Nuts M10-1.5 (Wheel/Stand) .............. 2
•
Cap Screws M8-1.25 x 50 (Jointer/Stand) . 3
•
Flat Washers 8mm (Jointer/Stand) ............ 6
•
Lock Washers 8mm (Jointer/Stand) ........... 3
•
Hex Nuts M8-1.25 (Jointer/Stand) .............. 3
•
Flat Washers 6mm (Handwheels) .............. 2
•
Cap Screws M6-1 x 12 (Handwheels) ....... 2
•
Set Screw M5-.8 x 12 (Cutterhead Guard) 1
•
Cap Screws M8-1.25 x 25 (Pedestal) ........ 2
•
Lock Washers (Pedestal) ........................... 2
•
Flat Washers (Pedestal) ............................. 2
•
Phillips Head Screws
M5-.8 x 16 (Dust Port) ................................ 4
•
Flat Washers 5mm (Dust Port) .................. 4
•
Cap Screws M8-1.25 x 25 (Fence Suppt.) . 4
•
Flat Wshers 8mm (Fence Support) ............ 4
•
Lock Washers 8mm (Fence Supptort) ....... 4
In the event that any nonproprietary parts are
missing (e.g. a nut or a washer), we would be
glad to replace them, or for the sake of expedi-
ency, replacements can be obtained at your local
hardware store.
Figure 3. Box 1 inventory contents.
A
B
C
D
E
F
G
H
Figure 4. Box 2 inventory contents.
J
K
L
M
SUFFOCATION HAZARD!
Immediately discard all plas-
tic bags and packing materi-
als to eliminate choking/suf-
focation hazards for children
and animals.
I