Graco BULLDOG 222248 - Manual (Page 13)

13 306–646
PARTS LIST – STANDARD PUMPS
Model 222–248, Series A
20:1 Ratio King Pump with Standard Air Motor
Includes items 1–66
Model 204–287, Series K
10:1 Ratio Bulldog Pump with Standard Air Motor
Includes items 1–66
Model 215–873, Series B
10:1 Ratio Bulldog Pump with Quiet Air Motor
Includes items 1–66
REF
NO. PART NO. DESCRIPTION QTY
REF
NO. PART NO. DESCRIPTION QTY
1 207–647 KING, STANDARD AIR MOTOR,
Model 222–248 only
see 306–968 for parts 1
215–255 BULLDOG, QUIET AIR MOTOR
Model 215–873 only
see 307–304 for parts
208–356 BULLDOG, STANDARD AIR MOTOR
Model 204–287 only
See 307–049 for parts 1
2 204–641 DISPLACEMENT PUMP ASSEMBLY
Series K Includes items 3–39, 56–66 1
3 205–161 .HOUSING, intake valve seal
Includes item 30 1
4 206–256 .VALVE, bleeder 1
6 100–155 .NUT, hex, jam; 5/8–18 1
7 101–354 .PIN, roll; 0.188” (4.8 mm) dia;
1.125” (28.6 mm) long 1
8 102–420 .BOLT, hex hd cap; 5/8–11 x 12” 4
11 158–440 .NUT, packing, intake valve 1
15 108–833* .O–RING, Viton r 1
17 108–832* .O–RING, Viton 1
18 162–887 .ROD, displacement 1
19 162–888 .CAP, lower 1
20 162–891 .ROD, connecting 1
21 186–058** .PACKING NUT/WET–CUP 1
26 181–896 .HOUSING, outlet 1
27 162–898* .GASKET, copper 3
28 162–900 .HOUSING, intake valve 1
29 162–901 .STOP, intake valve 1
30 162–902** .SEAT, intake valve (part of item 3) 1
31 162–903 .GUIDE, valve plate 1
32 162–906** .ROD, priming 1
33 164–442 .CAP, upper
1
34 165–888 .PLATE, valve 1
35 181–897* .BEARING, piston 2
36 165–890 .PLATE, valve 1
37 172–199 .PISTON, priming 1
38 181–893 .PISTON, cylinder 1
39 180–936 .CYLINDER, pump 1
41 100–103** PIN, cotter; 0.125” (3.2 mm) dia. x
1.5” (38 mm) long 1
42 100–104** PIN, cotter; 0.125” (3.2 mm) dia. x
1.75” (45 mm) long 1
44 101–712 NUT, lock; 5/8–11; w/nylon insert 3
45 101–936 NUT, hex, jam; 3/4” 1
47 158–674** O–RING, nitrile rubber 1
49 168–211 COUPLING, connecting rod
Model 222–248 only 1
161–543 COUPLING, connecting rod
Models 215–873 & 204–287 only 1
50 168–210 NUT, shouldered
Model 222–248 only 1
161–544 NUT, shouldered
Models 215–873 & 204–287 only 1
52 168–824 ROD, tie; 13–7/8” (352.4 mm) long,
shoulder to shoulder 3
53 168–253 ROD, connecting; 9–5/16” (236.5 mm)
Model 222–248 only 1
164–443 ROD, connecting; 9–3/8” (238.1 mm)
Models 215–873 & 204–287 only 1
56 108–543* PACKING, u–cup; UHMWPE 1
58 172–477*** TAG, warning (not shown) 1
64 223–369* GLAND/PACKING STACK, throat 1
65 223–368* GLAND/PACKING STACK,
intake valve
1
66 110–769 SEAL, wiper; polyurethane 1
*Included in repair kit 220–861.
**Recommended “tool box” spare parts. Keep on hand to
reduce down time.
***Extra warning labels and tags are available free.
306 and 307 numbers in descriptions refer to separate in-
struction manuals, supplied.
Displacement Pump Repair Kit 220–861
Must be purchased separately
Includes:
Ref No. Qty
27 3
35 2
56 1
64 1
65 1
NOTE: O–ring 104–445 included in the kit is not used
with these models.
HOW TO ORDER PARTS
1 To be sure you receive the correct replacement parts, kits or
accessories, always give all of the information requested in the
chart below.
2. Check the parts list to identify the correct part number; do not use
the ref. no. when ordering.
3. Order all parts from your nearest Graco distributor.
6 digit
Part Number Qty Part Description