FUNAI CDV210HH8 - Manual (Page 25)

EN – 25 –
cut here
1 Turn on the TV and set it to channel 3.
• If channel 3 has been already occupied for
broadcasting, see “RF Output Channel” section.
2 Select your language when turning this unit on for the first time.
Then press [B] to go to next step.
or
STANDBY-ON
Quick Use Guide
Please refer to “Basic TV Connection” on the front page before
you use this unit.
RF Output Channel
If channel 3 has been already occupied for broadcasting,
1) Set your TV to channel 4.
2) Insert a pre-recorded tape into this unit.
3) Press
[SOURCE] on the unit so that the VCR SOURCE light is
lit.
• If noise appears on the TV screen, press [VCR/TV] on the
remote control.
4) Press [PLAY B] once.
5) After a few seconds, press and hold [PLAY B] on the unit for
3 seconds.
• The RF output channel will change to channel 4 from channel
3 and you will see a playback picture.
• When a picture does not appear on the TV screen, repeat
step 4.
6) Press [STOP C] to stop playback.
1
Connections
Clock Setup 5
Turn on the Unit for the First Time
VCR/DVD Switching
4
3
Installing the Batteries for the Remote
Control 2
STANDBY-ON REW F.FWD STOP/EJECT PLAY RECORD CHANNEL
OPEN/
CLOSE
VCR DVD
PREV SOURCE STOP PLAY NEXT
DISC IN PLAY REC TIMER
IR
VCR DVD
SOURCE
DVD button
VCR button
STANDBY-ON
DISPLAY VCR DVD PAUSE
SLOW
VCR/TV
SKIP/CH.
PLAY
STOP
RECORD
MENU
SETUP TOP MENU
MODE ZOOM
SUBTITLE T-SET ANGLE
ENTER
RETURN
SEARCH MODE
REPEAT A-B
OPEN/CLOSE /EJECT SPEED AUDIO
CLEAR/ C. RESET
1 2 3
4 5 6
7 8 9
0 +10
SOURCE button
DVD SOURCE light
VCR SOURCE light
VCR MODE
Press [VCR] on the remote control. (Verify that the VCR SOURCE
light is lit.)
DVD MODE
Press [DVD] on the remote control. (Verify that the DVD SOURCE
light is lit.)
No Please wait for a few minutes.
After scanning...
• The tuner stops on the lowest memorized channel.
• You can select only the channels memorized in this unit by using
[SKIP/CH. G/K, H/L] (or [CHANNEL K/L]).
• If “AUTO SET UP” appears on the TV screen again, check the cable con-
nections. Then, press [B] once again.
Yes Press [MENU] to exit.
Do you connect the cable from the cable box or the satellite box to the
unit’s ANT-IN jack?
Hint
• Pressing only [SOURCE] on the front panel DOES NOT switch the mode
of the remote control. You MUST select the correct mode on the remote
control.
1 Press [MENU] and select “CLOCK SET“.
Then press [B] to go to next step.
2 Select the current month.
Then press [B] to go to next step.
3 Select the current day.
Then press [B] to go to next step.
4 Select the current year.
Then press [B] to go to next step.
5 Select the current hour.
Then press [B] to go to next step.
6 Select the current minute.
Then press [B] to go to next step.
7 Select “AM” or “PM”.
8 To exit the CLOCK SET screen
• If the clock is not set, the CLOCK SET screen appears when you
press [MENU]. In this case, go to step 2.
or
MENU
or
or
or
or
or
or
- M E N U -
TIMER
PROGRAMMING
AUTO REPEAT [OFF]
CHANNEL SET UP
B CLOCK SET
LANGUAGE
SELECT
CLOCK SET
MONTH DAY YEAR
1 0 / – – – – – –
HOUR MINUTE AM/PM
– – : – – – –
CLOCK SET
MONTH DAY YEAR
1 0 / 0 1 – – – –
HOUR MINUTE AM/PM
– – : – – – –
CLOCK SET
MONTH DAY YEAR
1 0 / 0 1 2 0 0 7
HOUR MINUTE AM/PM
– – : – – – –
CLOCK SET
MONTH DAY YEAR
1 0 / 0 1 MON 2 0 0 7
HOUR MINUTE AM/PM
0 5 : – – – –
CLOCK SET
MONTH DAY YEAR
1 0 / 0 1 MON 2 0 0 7
HOUR MINUTE AM/PM
0 5 : 4 0 – –
CLOCK SET
MONTH DAY YEAR
1 0 / 0 1 MON 2 0 0 7
HOUR MINUTE AM/PM
0 5 : 4 0 P M AM
B PM
LANGUAGE SELECT
B ENGLISH [ON]
FRANCAIS
ESPAÑOL
3 Press [ B ] to start Auto Set Up.
CH 01
AUTO SET UP
NO YES
VCR VCR
VCR VCR
2 3 1
E8C1UCD_EN.indd 25 E8C1UCD_EN.indd 25 2007/04/03 9:49:34 2007/04/03 9:49:34