Programming the remote – Harman-Kardon AVR 510 User Manual

Page 38

38 PROGRAMMING THE REMOTE

Programming the Remote

NOTE: While entering commands for Power
On/Off of any device during a macro sequence,
press the Mute button

. DO NOT press the

actual Power button.

3. When all the steps have been entered,

press the Sleep button

j to enter the

commands. The red light under the Input
Selectors

ef will blink and then

turn off.

Example: To program the Macro 1 button
so that it turns on the AVR 510, TV and a
Cable Box, follow these steps:
• Press the Macro 1 button

w and

Mute

buttons at the same time and

then release them.

• Note that the Program/SPL Indicator

will flash amber.

• Press the AVR Selector

• Press the Mute

button to store the

AVR 510’s power on command.

• Press the VID 2 Input Selector button

e to indicate the next command is for
“TV Power On.”

• Press the Mute

button to store the

TV Power On Command.

• Press the VID 3 Input Selector button

e to indicate the next command is for
“Cable Power On.”

• Press the Mute

button to store the

Cable Power On command.

• Press the Sleep/Channel Up button

to complete the process and store the
macro sequence.

After following these steps, each time you
press the Macro 1 button

w, the remote

will send the Power On/Off command.

Erasing Macro Commands
To remove the commands that have been
programmed into one of the Macro buttons,
follow these steps:

1. Press the Mute button

and the Macro

button

w that contains the commands

you wish to erase.

2. Note that the Program/SPL Indicator

c will flash amber, and the LED under
the AVR Selector

f will turn red.

3. Within ten seconds, press the Surround

Mode Selector/Channel Down
button

4. The red LED under the AVR Selector will

go out, and the Program/SPL Indicator
c will turn green and flash three times
before it goes out.

5. When the Program/SPL Indicator

goes out, the Macro has been erased.

Programmed Device Functions
Once the AVR 510’s remote has been pro-
grammed for the codes of other devices, press
the appropriate Input Selector

e to change

the remote from controlling the AVR 510 to con-
trolling the additional product. When you press
any one of the selectors, it will briefly flash in red
to indicate that you have changed the device
being controlled.

When operating a device other than the
AVR 510, the controls may not correspond
exactly to the function printed on the remote
or button. Some commands, such as the volume
control, are the same as they are with the
AVR 510. Other buttons will change their
function so that they correspond to a secondary
label on the remote. For example, the Sleep
and Surround mode selector buttons also func-
tion as the Channel Up and Channel Down
buttons when operating most TV sets, VCRs or
cable boxes. The Channel Up/Down indication is
printed directly on the remote. For many stan-
dard CD players, cassette decks, VCRs and DVD
functions, the standard function icons are printed
on top of the buttons.

For some products, however, the function of a
particular button does not follow the command
printed on the remote. In order to see which
function a button controls, consult the Function
List tables printed on page 41. To use those
tables, first check the type of device being con-
trolled (e.g., TV, VCR). Next, look at the remote
control diagram pictured at the left. Note that
each button has a number on it.

To find out what function a particular button
has for a specific device, find the button number
on the Function List and then look in the
column for the device you are controlling. For
example, button number 54 is the Macro 2
button for the AVR 510, but it is the “Favorite”
button for many cable television boxes and
satellite receivers. Button number 32 is the
Delay button for the AVR 510, but the + Time
button for CD players.

510

LIGHT