Operation – Harman-Kardon AVR 510 User Manual

Page 31

31 OPERATION

Operation

the Numeric Keys r that correspond to the
station’s frequency. The desired station will
automatically be tuned. If you press an incor-
rect button while entering a direct frequency,
press the Clear button

to start over.

NOTE: When the FM reception of a station is
weak, audio quality will be increased by
switching to Mono mode by pressing the
FM Mode button @

s until the

STEREO indicator V goes out.

Preset Tuning
Using the remote, up to 30 stations may be
stored in the AVR 510’s memory for easy recall
using the front panel controls or the remote.

To enter a station into the memory, first tune
the station using the steps outlined above.
Then:

1. Press the Memory button on

the

remote. Note that the MEMORY indicator U
will be illuminated and flash in the Main
Information Display

Û.

2. Within five seconds, press the Numeric
Keys

r corresponding to the location where

you wish to store this station’s frequency. Once
entered, the preset number will appear in the
Preset Number/Sleep Timer display

3. Repeat the process after tuning any
additional stations to be preset.

Recalling Preset Stations
• To manually select a station previously
entered in the preset memory, press the
Numeric Keys

r that correspond to the

desired station’s memory location.

• To manually tune through the list of stored
preset stations one by one, press the Preset
Stations Selector buttons

)`© on the

front panel or remote.

Tape Recording

In normal operation, the audio or video source
selected for listening through the AVR 510 is
sent to the record outputs. This means that any
program you are watching or listening to may
be recorded simply by placing machines con-
nected to the outputs for Tape Outputs ™ or
Video 1 or 2 Outputs ∞gj in the record
mode.

When a digital audio recorder is connected to
the Digital Audio Outputs

, you are able

to record the digital signal using a CD-R,
MiniDisc or other digital recording system.

In addition to the rear panel digital outputs, the
AVR 510 offers Harman Kardon’s exclusive con-
figurable front panel output jack feature. For
easy connection of portable devices, you may
switch the front panel Digital Coax jack

or the Video 4 jack

^ from an input to an

output by following these steps:

1.Press the OSD button

v to view the

MASTER MENU (Figure 1).

2.Press the Set button

p to enter the

IN/OUT SETUP menu (Figure 2).

3.Press the

button

n so that the on-

screen

›

cursor is next to VIDEO 4 or

COAXIAL 3 depending on which input
you wish to change to an output. Either
input, or both may be changed at any time.

4.Press the Set button

p and then press

either of the

‹

›

buttons

so that

the word IN is highlighted.

5.Press the Set button

p to enter the

change.

6.Press the OSD button

v to exit the menus

and return to normal operation.

Note that once the setting is made, the appro-
priate Input/Output Status Indicator

will turn red, indicating that the selected ana-
log or digital jacks are now an output, instead
of in the default setting as an input. Once
changed to an output, the setting will remain
as long as the AVR 510 is turned on, unless the
setting is changed in the OSD menu system, as
described above. Note, however, that once the
AVR 510 is turned off, the setting is cancelled.
When the unit is turned on again, the front
panel jacks will return to their normal default
setting as an input. If you wish to use their
jacks as an output at a future time, the setting
must be changed again using the OSD menu
system, as described above.

NOTES:
• The digital outputs are active only when a

digital signal is present, and they do not
convert an analog input to a digital signal,
or change the format of the digital signal.
In addition, the digital recorder must be
compatible with the output signal. For
example, the PCM digital input from a CD
player may be recorded on a CD-R or
MiniDisc, but Dolby Digital or DTS signals
may not.

• Please make certain that you are aware of

any copyright restrictions on any material you
copy. Unauthorized duplication of copyrighted
materials is prohibited by federal law.

Output Level Trim Adjustment

Normal output level adjustment for the
AVR 510 is established using the test tone, as
outlined on pages 23 and 24. In some cases,
however, it may be desirable to adjust the out-
put levels using program material such as a test
disc, or a selection you are familiar with.
Additionally, the output level for the subwoofer
can only be adjusted using this procedure.

To adjust the output levels using program
material, first set the reference volume for the
front left and front right channels using the
Volume Control

о.

If you are using a disc with test signals or an
external signal generator as the source from
which to trim the output levels, you may use
the EzSet feature of the remote to guide you to
the correct SPL level. To use the remote for this
purpose, press and quickly release the SPL
Indicator Select

to activate the sensor.

While the test tone is circulating, the
Program/SPL Indicator

c will change color

to indicate the level. Adjust the level as shown
above until the LED lights green for all chan-
nels. When it is red the level is too high; when
it is amber the level is too low. Press the SPL
Indicator Select

to turn the sensor and

indicator off.

Once the reference level has been set, press
the Channel Select button m

Ù and note

that FRONT L LEV will appear in the
Main Information Display

Y. To change

the level, first press the Set button

pÔ ,

and then use the Selector buttons

5 or the

⁄

buttons n to raise or lower the level.

DO NOT use the volume control, as this will
alter the reference setting.

Once the change has been made, press the Set
button

pÔ and then press the Selector

buttons

5 or the

⁄

buttons n to select

the next output channel location that you wish
to adjust. To adjust the subwoofer level, press
the Selector buttons

5 or the

⁄

buttons

n until WOOFER LEV appears in the
Main Information Display

Y or on-screen

display.