Program play – Harman-Kardon CDR 26 User Manual

Page 18

PROGRAM PLAY

18 PROGRAM PLAY

The CDR 26’s advanced programming system
enables you to program the order in which tracks are
played, to repeat one track or all tracks, or to repeat
any segment of a disc without regard to track
numbers.

Programming Playlists

To program the order of playback for the tracks on a
disc, insert the disc, let the unit read the Table of
Contents information, and wait until the disc has
stopped and the number of tracks and total running
time is displayed. Next, select the deck that will be
programmed by pressing the CDP Select Button
d on the remote for the Play Deck 3 or the CDR
Select Button

` on the remote for the Record

Deck

To begin the programming sequence, press the
Program Button

e on the remote or the Program

Button

˝ for the appropriate deck on the front

panel. The PROG Indicator

I will light and the

Information Display

Y will show 00 00 : 00.

Next, enter the track numbers to be played by press-
ing the Numeric Keys

p. For two-digit track num-

bers, be certain to enter the second digit within three
seconds after the first number is entered. If you are
programming your playlist using the front-panel con-
trols, use the Previous and Next Track Buttons

Ъ˘¸ to locate the desired track, then press the
Program Button

˝ for the appropriate deck to

enter the track into the sequence. As each track is
entered, the display will blink three times, alternating
between two displays. The first display will show the
track number just entered on the left side of the
Information Display

Y under the Track Time

Indicator

W, while the right side will flash the

number of steps that have been programmed. For
example, after programming the first step to be track
number 3, the display will flash 03 P-01.

If you make a mistake while programming a track, you
may press the Clear Button

h to delete the last

programmed track.

Alternating with the track number and program step
will be a display of the track and the total running time
of all tracks that have been programmed so far. For
example, a display of 06 11:25 will indicate that
track number six was the last track programmed, and
that the total time of all tracks so far is 11 minutes
and 25 seconds. The Total Time Indicators

will flash with this display to remind you of the dis-
play’s contents.

These displays will alternate three times, and then
show a steady display of the total time and last track
programmed.

Continue to add tracks in the order you wish to have
them played until the programming session is com-
plete. You may add up to 20 tracks, repeating a track
if desired, as long as the total number does not
exceed 20. If you exceed the 20-track limit, the dis-
play will read FULL. Tracks may also be added
using the Next

Ò˘z and Previous Buttons

Ú¸f to locate the track, and the Program
Button

e to enter that track to the programmed

sequence.

When the complete list of tracks has been entered,
press the Play Button

j. The tracks will

then play in the order they have been entered. Note
that a programmed list of tracks may also be recorded
if the disc being programmed is in the Play Deck

Follow the instructions on page 20 for complete
information on recording and dubbing.

Once you have programmed a playlist it will remain in
the unit’s memory until the disc is removed or the unit
is turned off. Thus, if you play through a programmed
list, simply press the Play Button

j again

to replay the list.

To cancel an entire program list while the program is
playing, press the Program Button

˝e and

note that the Program Indicator

I will go out. To

remove a total program list when the disc is stopped,
simply open and close the disc drawer. Whenever a
disc is removed or the unit is turned off, the program
list is erased.

Repeat Play

The CDR 26’s programming system enables you to
repeat a single track on a disc, the entire disc or a
specially programmed passage that you select. To
repeat all discs, use the Continuous Play mode and
press the Stop Button

(

v after the desired

number of repetitions has played. (See page 17 for
more information on the Continuous Play mode.)

Repeat One Track
To repeat the track you are currently listening to, press
the Repeat Button

g and note that the Repeat

Indicator

F and the Repeat Status Indicator H

will both light to display

Repeat 1. If the track is

changed by using the Next/Previous Skip Button
ÒÚ˘¸fz while the Repeat 1 mode is
active, the new track will now be repeated.

Once Repeat 1 playback has been started, it will con-
tinue until the unit is stopped by pressing the Stop
Button

(

v, or the disc deck is opened by

pressing the appropriate Open/Close Button
6$c

. When playback is stopped, the

Repeat sequence is erased and must be reentered if
you wish to repeat a track on another disc.

Repeat All Tracks
To repeat all the tracks on a disc in order, press the
Repeat Button

g twice while the disc is playing

and note that the Repeat Indicator

F and the ALL

Repeat Status Indicator

H will light. Once the Play

Button

j is pressed, the disc will play

through from beginning to end continuously, until the
Stop Button

(

v is pressed. The Repeat All

function may be cancelled at any time by pressing the
Repeat Button

g once until both the Repeat

Indicator

F and ALL Repeat Status Indicator H

go out. The Repeat All function is also canceled when
the disc drawer is opened.

Repeat A-B
The CDR 26 may be programmed to repeat any
section within a track, or a complete passage that
includes material from a series of consecutive tracks.

To program the unit for A-B Repeat play, first play the
disc and locate the point where you wish to begin
the repeated section. At the start point, press the
A-B Repeat Button

y and note that the Repeat

Indicator

F will light and the Repeat Status

Indicator

H will show an A and flash. Let the disc

play until the point at which the section to be repeated
will end. At that end point, press the A-B Repeat
Button

y again and note that the Repeat Status

Indicator

H will stop flashing and will light, showing

REPEAT A-B.

The unit will immediately begin to play the section you
have programmed, and continually repeat it.

To resume normal play, press the A-B Repeat Button
y. The Repeat A-B Indicators FH will go out,
and the disc will continue playing through to the end.
Stopping the disc or opening the disc drawer will auto-
matically cancel the Repeat A-B programming.