Godox VING V860IIN TTL Li-Ion Flash Kit for Cameras - Manual (Page 8)

1/4
1/8
1/16
1/32
1/64
1/128
10
2
4
8
20
50
70
20-50
2
4
8
16
30
40
60-100
2
4
8
12
20
40
Hz
Wireless Flash Shooting: Optic Transmission
This product is compatible with Nikon Creative Lighting System
(CLS). It can function as either an optic wireless master or slave
flash. As a master unit, it can control Nikon speedlights e.g. SB-
900 and SB-910 via wireless. As a slave unit, it can be controlled
by wireless signals of Nikon speedlights e.g. SB-900 and pop-up
flash commanders of Nikon cameras e.g. D7100/D7000/D800.
- 39 - - 40 -
Maximum Stroboscopic Flashes:
1/4
1/8
1/16
1/32
1/64
1/128
1
7
14
30
60
90
90
2
6
14
30
60
90
90
3
5
12
30
60
90
90
4
4
10
20
50
80
90
5
4
8
20
50
80
90
6-7
3
6
20
40
70
90
8-9
3
5
10
30
60
80
Flash
output Hz
Flash
output
● You can set up three slave groups for i-TTL autoflash shooting.
With i-TTL autoflash, you can easily create various lighting effects.
● Any flash settings for the slave units on the master flash in i-TTL /
Manual / RPT mode will be automatically sent to the slave units.
So the only thing you need to do is to set the master unit for each
slave group without any operation for the slave units at all during
the shooting.
● This flash can work in i-TTL / M / RPT / OFF flash modes when set
as a master unit.
Slave/Master Unit's Positioning and Operation Range
Indoors
Outdoors
15m ( 49 . 2ft )
10m ( 32 . 8ft )
80°
8m ( 26 . 2ft ) 12m ( 39 . 4ft )
Set the flash frequency and 3
flash times.
● Press Function Button 3
< > button to select
the item (blinks).
● Turn the Select Dial to set
the number and press
Function Button 4 < >
button again to confirm. The
next item to be set will blink.
● After you finish the setting,
press < SET > button and all
the settings will be
displayed.
Flash Mode — RPT: Stroboscopic Flash
With stroboscopic flash, a rapid series of flashes is fired. It can be
used to capture a multiple images of a moving subject in a single
photograph.
You can set the firing frequency (number of flashes per sec.
expressed as Hz), the number of flashes, and the flash output.
Press < MODE > button so 1
that < RPT > is displayed.
Turn the Select Dial to choose 2
a desired flash output.
Calculating the Shutter Speed
During stroboscopic flash, the shutter remains open until the firing
stops. Use the formula below to calculate the shutter speed and set
it with the camera.
For example, if the number of flashes is 10 and the firing frequency is
5 Hz, the shutter speed should be at least 2 seconds.
Number of Flashes / Flash Frequency = Shutter Speed
To avoid overheating and deteriorating the flash head, do not
use stroboscopic flash more than 10 times in succession.
After 10 times, allow the camera flash to rest for at least 15
minutes. If you try to use the stroboscopic flash more than 10
times in succession, the firing might stop automatically to
protect the flash head. If this happens, allow at least 15
minutes’ rest for the camera flash.
● Stroboscopic flash is most effective with a highly reflective
subject against a dark background.
● Using a tripod and a remote control is recommended.
● A flash output of 1/1 and 1/2 cannot be set for stroboscopic
flash.
● Stroboscopic flash can be used with“ buLb ”.
● If the number of flashes is displayed as “--”, the firing will
continue until the shutter closes or the battery is
exhausted. The number of flashes will be limited as shown
by the following table.
MULTI
Hz