i-PRO WV-QED100G-W Ceiling Mount Bracket (Smoke) - Manual (Page 2)

FRONT
LOCK
F RONT
FRONT
LOCK
F RONT
F RONT
Cable inlet
FRONT mark
Run the cables from the cable inlet.
IMPORTANT:
• The cables shall be run from the opposite
side of the FRONT mark. Failure to observe
this makes the cables unconnectable since
the camera faces the opposite side.
Step 9
Step 10
Prepare the cables.
Attach the inner cover.
① Put the camera onto the camera mounting plate
with aligning the lock plate of the camera with
the guide of the camera mounting plate and
inserting the center of the camera mounting
plate with the center of the camera, and turn the
camera clockwise.
② Secure the camera with the camera fixing screw
(M3: camera accessory).
Recommended tightening torque:
0.68 N·m {0.5 lbf·ft}
IMPORTANT:
• Be sure to mount the camera with holding the
stationary portion of the camera.
① Align the marks ( Ⓐ to Ⓐ and Ⓑ to Ⓑ ) between
the camera mounting plate and mounting base.
② Mount the camera mounting plate on the
mounting base with aligning
g of the camera
mounting plate with “START h ” of the mounting
base.
③ Turn the camera mounting plate until g of the
camera mounting plate aligns with “END h ” of
the mounting base, and then temporarily fix by
hooking the hooks of the camera mounting
plate into the holes of the mounting base.
④ Tighten the 3 screws that were removed in
Step 2.
Recommended tightening torque:
1.6 N·m {1.18 lbf·ft}
IMPORTANT:
• Do not let the cables be caught during
installation work.
① Mount the decorative cover on the camera mount-
ing plate with engaging the projections of the
decorative cover with the hooks for the decorative
cover.
② Turn the decorative cover clockwise while pressing
the projections upward and fix it temporarily.
IMPORTANT:
• The i-PRO logo, shall be aligned with the
FRONT mark.
Step 11 Mount the camera on the camera mounting plate.
FRONT
LOCK
Stationary portion
Center of the camera
mounting plate
Camera fixing
screw
Lock plate
Guide
Rotating portion
Connect the safety wire locked on the
mounting base to the camera.
Make sure that the apical ring of the safety
wire is engaged with the safety wire hook of
the camera by pulling the safety wire after
connection.
F RONT
FRONT
LOCK
Mounting base
Safety wire
Safety wire hook
Step 12
Step 13
Step 14
Step 15
Step 16
Step 17
Connect the safety wire to the camera.
Connect the cables to the camera.
Mount the camera mounting plate and camera on the mounting
base.
Mount the decorative cover.
Tighten the fixing screw to be used for cover fall prevention.
Remove the protection sheet from the dome cover.
ST AR T
EN D
F RONT
FR ON T
LOCK
Mounting base
Camera mounting plate
Align Ⓐ with Ⓐ
Align Ⓑ with Ⓑ
Projections
Hooks for the
decorative cover
(3 places)
Fixing screw to be used for cover fall prevention
Recommended tightening torque:
1.6 N·m {1.18 lbf·ft}
Note:
• When the tilt angle of the camera is almost level, the upper side of images will be hidden by this
product reflecting on the screen. In such a case, adjust the tilt angle. Refer to the Operating
Instructions of the camera for further information.
② Attach the inner cover.
„ „ When removing the inner cover
Release the claws on the inner surface on both the left and right sides one by one and
then remove the inner cover.
① Remove the side covers from the camera main body. (Both the left and right sides)
Click feeling
A click sound
is heard.
Claws on the
inner surface