i-PRO WV-QWL500 Wall Mount Bracket (White) User Manual

Operating instructions, Standard accessories, Other items that are needed (not included)

Caution:

⿟

Before attempting to connect or operate this product, please read these instructions carefully.

Notice:

⿟

This equipment is not suitable for use in locations where children are likely to be present.

⿟

Do not install this product in locations where ordinary persons can easily reach.

⿟

For information about screws and brackets required for installation, refer to the

corresponding section of this document.

Standard accessories

Operating Instructions (this document)

.......

1 pc. Fixing screws for attachment plate .......... 5 pcs.

(M4 x 8 mm {5/16 inches}) (of them, 1 for spare)

Other items that are needed (not included)

Fixing screws (M4) ................................................................................................................... 4 pcs.

IMPORTANT

⿟

Minimum pullout strength: 196 N {44 lbf} (per 1 pc.)

⿟

This value indicates the minimum pull-out strength required value per screw. For information

about the minimum pull-out strength, refer to our support website .

⿟

Select screws according to the material of the location that the camera will be mounted to.

In this case, wood screws and nails should not be used.

Precautions for installation



In order to prevent injury, the product must be securely mounted to the wall according to

the Installation Guide of this bracket.



Mounting method for this product

This product is for attaching to a wall. If the product is mounted on a desktop or at a slant, the

camera may not work correctly and its lifetime may be shortened.



Make sure to remove this product if it will no longer be used.

Compact dome type
WV-S31xx, S35xx series

Indoor 360-degree panoramic type
WV-S41xx series

Outdoor dome type
WV-S25xx series

NOTE

⿟

When an outdoor 360-degree panoramic type camera is attached using this product, it will be
close to the wall surface, so the infra-red light built into the camera will have an effect on the
images taken. Additional information on omnidirectional shooting using an IR LED is
available at the Website below.
https://security.panasonic.com/training_support/support/info/

The installation instructions from hereon use the installation of the WV-S2531LN (outdoor dome
type) on a wall using this product as an example. The procedure for installation is the same for
other cameras. When installing by combining this product with other brackets, refer to the
Operating Instructions for the other brackets as well.

Step 2

Decide the location where this product is to be attached on the wall, then
make the holes for fixing and wiring as shown in the below illustration.

* Determine the diameter and depth of the holes

according to the specifications of the fixing
screws (4 pcs.) (M4: procured separately).

NOTE

⿟

When wiring using the “wiring hole on the
side” of the camera, the “wiring hole” in the
illustration at right is not necessary.

Step 3

Thread the cables through this product, then fix to the wall.

NOTE

⿟

When installing outside, waterproof the
wiring hole and the holes for the fixing
screws.

Fixing screws (4 pcs.) (M4: locally procured)
Minimum pullout strength:
196 N {44 lbf} (per 1 pc.)

Wiring hole on the side

Wiring hole

ø30 mm

{1-3/16 inches}

46 mm

{1-13/16 inches}

83.5 mm

{3-9/32

inches}

This product

Cables

100 mm {3-15/16 inches}

Fixing screws

Step 6

Remove the camera enclosure (when installing a camera type
other than the indoor dome type), then tighten the camera fixing
screws (red) to fix the camera firmly.

Camera fixing

screw (red)

Enclosure fixing

screws (4 places)

Bit

(camera accessory)

Step 7

After adjusting the angular field of view of the camera, fix the
enclosure to the original poisition.
Refer to the Installation Guide for the camera for detailed
adjustment methods.

Recommended tightening torque

: 0.78 N·m {0.58 lbf·ft}

NOTE

⿟

The recommended tightening torque for the screws depends on the camera you are
using. Refer to the Installation Guide for each camera.

Step 4

Connect the cables to the camera.

The following waterproofing procedures are
not necessary for indoor installations. Connect
directly to the camera.

Connect the RJ45 network cable and the

Ethernet cable.

NOTE

⿟

Refer to the Installation Guide for the
camera for information on how to
assemble the waterproof connector.

If necessary, also connect and waterproof other

cables as shown in the illustration at right.

IMPORTANT

⿟

Stretch the tape by approx. twice and wind
it around the cable.

⿟

Start and finish winding the waterproof
tape so that it overlaps the external covers
of the cables by approximately 20 mm
{25/32 inches}.

Step 5

Attach the camera to this product and temporarily fix.

Approx. 15°

Holes of the attachment

plate (4 places)

Attachment mounting

screws (2 places)

NOTE

⿟

Refer to the Installation Guide for the camera for information on how to attach.

RJ45

waterproof

jack

RJ45 plug

(locally procured)

RJ45 waterproof

connector cover

(camera accessory)

RJ45 waterproof

connector cap

(camera accessory)

RJ45 Network cable

Ethernet cable

Waterproof tape (camera accessory)

Approx. 20 mm {25/32 inches}

Approx. 20 mm

{25/32 inches}

Wind the tape in a

half-overlapping

manner.

Step 8

Attaching the compact dome type WV-S31xx, S35xx series

Process the installation surface according to the description in

Step 2.

Referring to the description in

Step 3, thread the network cable through this product (the

attachment plate is not attached) to fix it in place.

Either connect the RJ45 waterproof connector according to

Step 4, or for the indoor model,

attach the network cable directly to the camera.

Fix the camera to this product. The camera can be attached in the forward facing direction or

rotated at ±90° to the left or right. When shooting close to the wall, change the fixing position
by ±90° in either direction.
Refer to the Installation Guide for the camera for detailed attachment methods.
The following illustration shows an example of installing an indoor compact dome type
WV-S31xx series.

Left 90°

Right 90°

Front

Fixing positions for screws when using

an outdoor compact dome type
WV-S35xx series
(Front, rotated 90° left, rotated 90° right)

Fixing positions for screws when using
an indoor compact dome type
WV-S31xx series

(Front, rotated 90° left, rotated 90° right)

Recommended tightening torque

: 0.78 N·m {0.58 lbf·ft}

NOTE

⿟

When fixing a compact dome type
camera, of the three fixing positions, use
the 2 forward places to fix.



Right 90°

Left 90°



Front

Installation

Step 1

Remove the enclosure from the

camera body.

For compact dome types and indoor
dome types of cameras, the enclosure
is removed before installation.
Refer to the parts describing
installation in the Installation Guide for
each camera for information on how to
remove the enclosure.

For models other than the compact dome type WV-S31xx, S35xx series, attach the attachment

plate (camera accessory) to this product using the fixing screws for attachment plate.

■

When attaching using the attachment plate included with the camera

(Recommended tightening torque: 0.78 N·m {0.58 lbf·ft})

NOTE

⿟

When attaching an indoor 360-degree panoramic type camera, the “TOP” mark direction on
the attachment plate will be in the direction of the Panasonic logo after the camera is installed.

■

When attaching the camera directly to this product

(Compact dome type WV-S31xx, S35xx series)

The attachment plate is not used.

Enclosure

Fixing screws for attachment plate

(4 pcs.) (M4: accessories)

Indoor 360-degree panoramic type
WV-S41xx series

Outdoor dome type
WV-S25xx series



Step 2



Step 8

For U.S. and Canada:

Panasonic i-PRO Sensing Solutions

Corporation of America

800 Gessner Rd, Suite 700 Houston, TX 77024

https://www.security.us.panasonic.com/

Panasonic Canada Inc.

5770 Ambler Drive, Mississauga, Ontario, L4W 2T3 Canada

1-877-495-0580

https://www.panasonic.com/ca/

For Europe and other countries:

Panasonic Corporation

http://www.panasonic.com

Panasonic i-PRO Sensing Solutions Co., Ltd.

Fukuoka, Japan

Authorised Representative in EU:

Panasonic Testing Centre

Panasonic Marketing Europe GmbH

Winsbergring 15, 22525 Hamburg, Germany

Preface

This product is used to attach dome-type cameras facing down on a wall.
For the latest information about the supported cameras, refer to our support website
(https://security.panasonic.com/training_support/support/info/C0112>).

Specifications

Ambient operating temperature: –50 °C to +60 °C {–58 °F to +140 °F}
Dimensions:

158 mm (W) × 112 mm (H) × 188 mm (D)
{6-7/32 inches (W) × 4-13/32 inches (H) × 7-13/32 inches (D)}

Mass:

Approx. 520

{1.15 lbs}

Finish:

Aluminum die cast

WV-QWL500-W : i-PRO white
WV-QWL500-G : Light gray

Precaution



Refer installation work to the dealer.

Installation work requires technique and experience. Failure to observe this may cause fire,
electric shock, injury, or damage to the product.
Be sure to consult the dealer.



Install the product securely on a wall in accordance with the installation instructions.

Failure to observe this may cause injury or accidents.



Do not use this bracket except with suitable cameras.

Failure to observe this may cause a drop resulting in injury or accidents.



Do not install this product on a place that is greatly influenced by wind.

Installation on a place where the wind speed is 60 m/s {approx. 134 mph} or more may cause a
fall of the product resulting in injury or accidents.



The measures of protection against snowfall shall be taken.

Weight of snow may cause a fall of the product resulting in injury or accidents.
Protect the product against snowfall by installing it under eaves.

When using this product, also read the “Precautions” described in the operating
instructions for the camera to be attached.

Operating Instructions

Included Installation Instructions

Wall Mount Bracket

Model No.

WV-QWL500-W

WV-QWL500-G

⿟

Before attempting to connect or install this product, please read these instructions carefully
and save this manual for future use.

⿟

The external appearance and other parts shown in this manual may differ from the actual
product within the scope that will not interfere with normal use due to improvement of the
product.

Panasonic i-PRO Sensing Solutions Co., Ltd. assumes no responsibility for injuries or

property damage resulting from failures arising out of improper installation or

operation inconsistent with this documentation.

Fs0320-0

Printed in China

WV-QWL500_PGQX2359ZAC1_カメラ壁取付金具.indd 1

2020/05/07 16:37:34

This manual is related to the following products:

WV-QWL500 Wall Mount Bracket (Gray)