Flash mode — ttl autoflash, Flash mode — m: manual flash, Fec: flash exposure compensation – Godox AD200 TTL Pocket Flash with Barndoor Kit User Manual
Page 7: High-speed sync

Flash Mode — TTL Autoflash
This flash has three flash modes: TTL, Manual (M), and Multi (Stroboscopic). In TTL mode, the camera and the
flash will work together to calculate the correct exposure for the subject and the background. In this mode, multiple
TTL functions are available: FEC, FEB, FEL, HSS, second curtain sync, modeling flash, control with the camera’s
menu screen.
* Press < > Mode Selection Button and three flash modes will display on the AV panel one by one with each
pressing.
TTL Mode
Press <
> Mode Selection Button to enter TTL mode. The AV panel is displayed
<
TTL
>.
FEC: Flash Exposure Compensation
With FEC function, this flash can adjust from -3 to +3 in 1/3rd stops. It is useful in situations where minor adjusting
of the TTL system is needed based on the environment.
Setting FEC:
Press the <
SET
> Function
1
Button and flash exposure
compensation amount will be
highlighted on the AV panel.
Set the flash exposure
2
compensation amount.
●
Turn the Select Dial to set
the amount.
●
“0.3”means 1/3 step,
“0.7”means 2/3 step.
●
To cancel the flash exposure
compensation, set the
amount to “+0”.
Press <
SET
> button again to
3
confirm the setting.
GR/CH
/C.Fn
MODE/
RST
H
sec
min
Hz
MK
12
GR/CH
/C.Fn
MODE/
RST
H
sec
min
Hz
MK
12
GR/CH
/C.Fn
MODE/
RST
H
sec
min
Hz
High-Speed Sync
High Speed Sync (FP flash) enables the flash to synchronize with all camera shutter speeds. This is convenient
when you want to use aperture priority for fill-flash portraits.
Please use the X1 series
2
transmitter to trigger.
Long Press Function Button
1
< > for 2 seconds so that
< > is displayed.
●
With high-speed sync, the faster the shutter speed, the shorter the effective flash range.
●
Multi flash mode cannot be set in high-speed sync mode.
●
Over-temperature protection may be activated after 20 consecutive high-speed sync flashes.
GR/CH
/C.Fn
MODE/
RST
H
sec
min
Hz
MK
12
H
1/4
1
/
2
1/1
1/1–0.3
1/2+0.7
1/1-0.7
1/2+0.3
1/2-0.3
1/4+0.7
1/2-0.7
1/4+0.3
······
······
The flash output is adjustable from 1/1 full power to 1/128th power in 1/3rd stop increments. To obtain a correct
flash exposure, use a hand-held flash meter to determine the required flash output.
Press <
> button so that
1
<
M
> is displayed.
Turn the Select Dial to choose
2
a desired flash output amount.
Flash Output Range
The following table makes it easier to see how the stop changes in terms of f/stop when you increase or decrease
the flash output. For example, when you decrease the flash output to 1/2, 1/2-0.3, or 1/2-0.7, and then increase the
flash output to more than 1/2, 1/2+0.3, 1/2+0.7, and 1/1 will be displayed.
Figures displayed when reducing flash output level
→
←
Figures displayed when increasing flash output level
Press <
SET
> button again to
3
confirm the setting.
Flash Mode
— M: Manual Flash
GR/CH
/C.Fn
MODE/
RST
H
sec
min
Hz
MK
12
GR/CH
/C.Fn
MODE/
RST
H
sec
min
Hz
MK
12
GR/CH
/C.Fn
MODE/
RST
H
sec
min
Hz
MODE/
MODE/
MODE/
- 33 -
- 34 -