Sony WI-C300 Wireless In-Ear Headphones (Red) - Manual (Page 13)

Conn
ec
tio
n
s
a
nd
Op
er
at
ions
Connections
13 GB
Connecting example Default settings for the IP connection
1
Set the DIP 2 switch 8 to ON to perform settings of
cameras and IP remote controllers (Setting update
mode). Then turn the unit on by pressing the
1
switch.
The GROUP/POSITION and CAMERA buttons
flash in green while the unit is in the setting update
mode.
Notes
• Keep all the cameras and IP remote controllers
turned on while setting. Do not turn off any
camera or IP remote controller while setting.
• When turning on the unit, do not touch the
joystick until the GROUP/POSITION and
CAMERA buttons start flashing in green (for
detecting an origin point).
• When turning on the unit, do not operate the unit
until the GROUP/POSITION and CAMERA
buttons start flashing in green.
When you use the signal of the TALLY/CONTACT
connector in the NORMAL TALLY mode, the
selected camera may be changed by this signal. To
prevent this, remove the connection of the TALLY/
CONTACT connector or set to the ON AIR TALLY
mode.
2
Perform the following settings from the PC by
using the setting software “RM-IP Setup Tool.”
For details on the settings, refer to the “RM-IP
Setup Tool guide.”
Note
Until about 35 seconds after a camera turns on or is
rebooted, settings cannot be changed.
• Set the IP address* and name of the IP remote
controller
• Assign each camera to a camera number
(CAMERA button), and the camera group
number (GROUP/POSITION button) that the
camera number belongs to (7 camera numbers in
each of 16 camera group numbers, a total of up to
112 cameras). (Camera table setting)**
* If there is a different segment, connect the PC
to that segment and perform the settings. If you
do not use a gateway, set “Gateway address” to
0.0.0.0.
**To assign a camera of a different segment, use
the Export function of “RM-IP Setup Tool.”
• Create a “Camera List” csv file for each
segment.
• Create a “Camera Table” csv file for the IP
remote controller that you want to assign.
RGB/COMPONENT VISCA RS-422
1 2 3 4 5 6 7 8 9
EXT SYNC IN
IR SELECT
75
1 2 3
OFF ON HD SD
IN VISCA RS-232 OUT SDI OUT DC IN 12V
R
VIDEO S VIDEO
SDI OUT LAN
1 2 BRBK-IP10
ON
HD SD
OFF DATA MIX
RGB/COMPONENT VISCA RS-422
1 2 3 4 5 6 7 8 9
EXT SYNC IN
IR SELECT
75
1 2 3
OFF ON HD SD
IN VISCA RS-232 OUT SDI OUT DC IN 12V
R
VIDEO S VIDEO
SDI OUT LAN
1 2 BRBK-IP10
ON
HD SD
OFF DATA MIX
RGB/COMPONENT VISCA RS-422
1 2 3 4 5 6 7 8 9
EXT SYNC IN
IR SELECT
75
1 2 3
OFF ON HD SD
IN VISCA RS-232 OUT SDI OUT DC IN 12V
R
VIDEO S VIDEO
SDI OUT LAN
1 2 BRBK-IP10
ON
HD SD
OFF DATA MIX
MODE VISCA
1 9 1 9
RS-422 TALLY/CONTACT RS-232C !
DC 12V
LAN
MODE VISCA
1 9 1 9
RS-422 TALLY/CONTACT RS-232C !
DC 12V
LAN
Switching hub
(10BASE-T/100BASE-TX,
commercially available)
BRC-H900
to the AC adaptor
BRBK-IP10
IP control card (optional) LAN
connector
to the AC adaptor
BRBK-IP10
IP control card (optional) LAN
connector
BRC-H900
to the AC adaptor
BRBK-IP10
IP control card (optional)
LAN
connector
BRC-H900
to the AC adaptor
(supplied)
LAN
connector
to the AC adaptor
(supplied)
LAN
connector
LAN
connector
PC for setting
LA
N ca
b
le
(cat
egor
y
5 or
m
o
re
,
com
m
er
ciall
y
a
v
ai
lab
le)