2GIG GB1-345 Glass Break - Manual (Page 2)

Mounting
1 Place the Glass Break Detector base on the opposite wall or adjacent
wall to the window being protected.
2 Affix the base to the desired location utilizing the 3 long mounting
screws with anchors that are supplied.
TIP: For wall mounting the test button should be oriented down
nearest the floor.
IMPORTANT: When attaching the detector to the base, match the
alignment marks and twist clockwise. If batteries are not present,
the red tabs must be held away from the detector.
Inserting and Replacing Batteries
If a supervised Glass Break Detector battery is low, a low battery
notification is indicated on the Control Panel’s touch screen. If indicated,
replace the battery immediately. Use only the recommended
replacement batteries (See Specifications).
•
Remove the cover by twisting counterclockwise. Use only the
recommended replacement batteries (see Specifications).
WARNING: Improper handling of lithium batteries may result in heat
generation, explosion or fire, resulting in personal injuries.
Replace only with the same or equivalent type of battery as
recommended by the manufacturer (see Specifications).
Batteries must not be recharged, disassembled or disposed of in fire.
Disposal of used batteries must be made in accordance with the
waste recovery and recycling regulations in your area. Keep Away
From Small Children. If batteries are swallowed, promptly seek
medical attention.
California Only: This Perchlorate warning applies only to Manganese
Dioxide Lithium cells sold or distributed ONLY in /California, U.S.A.
Perchlorate Material‐special handling may apply. See dtsc.ca.gov/
hazardouswaste/perchlorate.
Specifications
FCC and Industry Canada Regulatory Information
This device complies with Part 15 of the FCC's Rules. Operation is subject
to the following two conditions:
1
This device may not cause harmful interference, and
2 This device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following
measures:
•
Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This product complies with FCC radiation exposure limits for an
uncontrolled environment. Avoid operating this product at a distance less
than 20 cm from the user.
WARNING: Any changed or modifications not expressly approved by
the party responsible for compliance could void the user's
authority to operate this equipment.
Limited Warranty
This 2GIG Technologies product is warranted against defects in material
and workmanship for 1 year. This warranty extends only to wholesale
customers who buy direct from 2GIG Technologies or through 2GIG
Technologies’ normal distribution channels. 2GIG Technologies does not
warrant this product to consumers. Consumers should inquire from their
selling dealer as to the nature of the dealer’s warranty, if any.
There are no obligations or liabilities on the part of 2GIG Technologies for
consequential damages arising out of or in connection with use or
performance of this product or other indirect damages with respect to
loss of property, revenue, or profit, or cost of removal, installation, or
reinstallation. All implied warranties for functionality, are valid only until
the warranty expires. This 2GIG Technologies Warranty is in lieu of all
other warranties expressed or implied.
For technical support in the USA and Canada
855-2GIG-TECH (855-244-4832)
For technical support outside of the USA and Canada
Contact your regional distributor
Visit 2gig.com for a list of distributors in your region
PN 77‐000004‐001 Rev F
2GIG Copyright © 2013. All rights reserved.
Wireless Signal Range 350 ft, open air, with 2GIG Wireless Control Panel
Code Outputs Alarm; Alarm Restore; Supervisory; Low Battery
Transmitter Frequency 345.000 MHz (crystal controlled)
Transmitter Frequency Tolerance ±15kHz
Transmitter Bandwidth
24kHz
Modulation Type Amplitude Shift Keying‐On/Off Keying (ASK‐OOK)
Unique ID Codes Over one million different code combinations
Supervisory Interval 70 minutes
External Input Sampling Current 20 uA
External Input
24V AC Standard doorbell circuit
Sensor Dimensions (HxD) 2.75 x 1.17 x 0.63 in. (6.98 x 2.97x 1.60 cm)
Weight (including battery and
magnet) 1.1 oz. (31.2 g)
Housing Material ABS plastic
Color White
Operating Temperature Limits 14° to 104° F (‐10° to 40° C)
Relative Humidity 5‐95% Non‐Condensing
Battery (installed with pull tab) One Panasonic CR2032 or equivalent Lithium
batteries
Included Accessories Four Phillips flat‐head screws