Bosch GST 18 V-LI Professional - Manual (Page 15)

English | 15
Bosch Power Tools 1 609 92A 00V | (12.11.12)
24 Locking screw for parallel guide*
25 Parallel guide with circle cutter*
26 Centring tip of the circle cutter*
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.
Technical Data
Noise/Vibration Information
The vibration emission level given in this information sheet has
been measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with another.
It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or poorly maintained,
the vibration emission may differ. This may significantly in-
crease the exposure level over the total working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may signif-
icantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep hands warm, organise work patterns.
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under “Technical Data” is in conformity with the fol-
lowing standards or standardization documents: EN 60745
according to the provisions of the directives 2011/65/EU,
2004/108/EC, 2006/42/EC.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
D-70745 Leinfelden-Echterdingen
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
Leinfelden, 22.10.2012
Assembly
 Before any work on the machine itself (e. g. mainte-
nance, tool change, etc.) as well as during transport
and storage, remove the battery from the power tool.
There is danger of injury when unintentionally actuating
the On/Off switch.
Battery Charging
 Use only the battery chargers listed on the accessories
page. Only these battery chargers are matched to the lith-
ium ion battery of your power tool.
Note: The battery is supplied partially charged. To ensure full
capacity of the battery, completely charge the battery in the
battery charger before using your power tool for the first time.
The Lithium-Ion battery can be charged at any time without
reducing its service life. Interrupting the charging procedure
does not damage the battery.
The Lithium-Ion battery is protected against deep discharging
by the “Electronic Cell Protection (ECP)”. When the battery is
empty, the machine is switched off by means of a protective
circuit: The inserted tool no longer rotates.
 Do not continue to press the On/Off switch after the
machine has been automatically switched off. The bat-
tery can be damaged.
The battery is equipped with a NTC temperature control
which allows charging only within a temperature range of be-
tween 0 °C and 45 °C. A long battery service life is achieved
in this manner.
Observe the notes for disposal.
Cordless Jigsaw GST 14,4 V-LI GST 18 V-LI
Article number 3 601 E8J 4.. 3 601 E8J 3..
Rated voltage V= 14.4 18
Stroke rate at no load
n
0
min -1 0 –2500 0 –2700
Stroke mm 23 23
Cutting capacity,
max.
– in wood
– in aluminium
– in non-alloy steel
mm
mm
mm 90
20
8
90
20
8
Bevel cuts
(left/right), max.
° 45 45
Weight according to
EPTA-Procedure
01/2003
kg 2.1/2.3* 2.2/2.4*
* dependent of the battery pack being used
GST 14,4 V-LI GST 18 V-LI
Measured sound values determined
according to EN 60745.
Typically the A-weighted noise levels
of the product are
Sound pressure level
Sound power level
Uncertainty K=
Wear hearing protection!
dB(A)
dB(A)
dB
80
91
3
81
92
3
Vibration total values a
h
(triax vector
sum) and uncertainty K determined
according to EN 60745:
Cutting board:
a
h
K
Cutting sheet metal:
a
h
K
m/s 2
m/s 2
m/s 2
m/s 2
5.5
1.5
6.5
1.5
6
1.5
8.5
1.5
Dr. Egbert Schneider
Senior Vice President
Engineering Helmut Heinzelmann
Head of Product Certification
PT/ETM9
OBJ_BUCH-1257-003.book Page 15 Monday, November 12, 2012 3:46 PM