Panasonic CX-DH801U - Manual (Page 32)

63
CX-DH801U
36
English
62
CX-DH801U
35
English
Electrical Connection
Overview
Cautions:
• This unit is designed for use in a car having a 12 V negative ground battery system.
• Be sure to insulate any exposed wires from the car chassis. Bundle all cables and keep cable terminals free from
any metal parts.
• Note that if your car has a driving computer or a navigation computer, disconnecting the cable from the battery may
clear the memory.
• Run the cords avoiding the spots where the temperature can be extremely high.
Note:
• To prevent from damage to the unit, be sure to follow the wiring diagrams below.
• Be sure to fully plug in the connectors. Secure them with clamps and tapes.
• All other installation methods require the use of dedicated metal fittings. Consult with a qualified servicing engineer
or your dealer if other methods are required.
ACC
PARKING BRAKE
H A
M4X5mmMAX
B C
V
H.A
H
C V.A.B
V
B
C
REMOTE-IN
REMOTE-OUT
BATTERY 5A
VIDEO-CONT
REMOTE-IN
POWER
DVD Changer
CX-DH801U
u Extension Cord
(BRAKE/VIDEO-CONT/ACC/BATT/DIN/RCA/GND)
Remote Control Sensor o
Ground Lead
To a clean, bare metallic part
of the car chassis
Parking brake connection lead
Be sure to wire the parking
brake for safety and preventing
Accident.
Video control lead (output)
To Video control lead (input) of
other equipment
Power Lead
To ACC power, + 12 V DC.
Battery Lead
To the car battery, continuous
+ 12 V DC.
(Black)
(Blue/yellow stripe)
(Green/yellow stripe)
(Red)
(Yellow)
Remote-In (Mini. Pin)
To the remote control sensor or
Remote-out of other equipment
Remote-Out (RCA)
To Remote-In of other equipment
such as TV tuner
Remote-In (RCA)
To Remote-out of other equipment
DIN Cable
To the changer connector
Video output
RCA Cable
Audio output (R)
Audio output (L)
(Black)
(Black)
(Black)
(Black)
(Yellow)
(Red)
(White)
Fuse 5 A
Attaching the remote control sensor o
Double-Faced Adhesive
Tape !2
Attach the
receiver.
Use the remote control
sensor extension cord
!0 if the original
remote control sensor
cord cannot reach the
DVD changer unit.
Note: The remote control sensor should be installed where
it is not exposed to direct sunlight and where it does not
interfere with driver’s operations.
Installation
(Continued)
Typical horizontal installation
1
Mount a mounting bracket (L) or (R) on either side of
the control unit with a hex. bolt together with double
washers (4 mm
x 8 mm).
Mounting bracket (L) r
Mounting bracket (R) t
Hex. bolt with double
washers (4 mm
x 8 mm) q x 4
Typical vertical installation
Mount the unit with the mounting bracket on either side
with a hex. bolt with double washers (4 mm
x 8 mm).
Mounting bracket (L) r
Mounting bracket (R) t
Hex. bolt with double
washers (4 mm
x 8 mm) q x 4
2
Select a location where the unit should be mounted.
Fix the base brackets with a double-faced adhesive
tape.
Base bracket w x 2
Double-faced adhesive tape y x 2
3
Use a cutter to cut a small cross in the carpet in
accordance with the locations of the 5 mm
bolts of
the base brackets.
Base bracket w x 2
Carpet
Fix both the base brackets and the double-faced adhesive
tape to a mounting surface below the carpet.
4
Mount the unit on the carpet with four hex. nuts
(5 mm
).
Hex. nut (5 mm ) e x 4
Carpet
Relationship between mounting
holes and angles
The relationship between mounting holes and angles of the
mounting brackets (L and R) is illustrated above. Symbols
corresponding to the mounting angles are marked near the
respective holes. Select the correct holes in accordance
with the mounting angles to be used.
Mounting bracket (L) Mounting bracket (R)
Fix the Remote Control
Sensor Cord with1 Cord
Clamp !1
Installation, Electrical Connection