Sony 5500 - Manual (Page 53)

53
4-2 HOME Menu
C
h
ap
te
r 4
M
enu
Se
tt
in
g
s
For detail on the procedure for DMC editing, see “6-2-1
DMC Editing” on page 126.
4-2-8 Setting the Stop Code (STOP
CODE)
You can select the stop code detection mode (recording/
confirmation/deletion), and adjust the stop position when a
stop code is detected.
To call up the STOP CODE menu screen
Press the ALT/[F8] (STOP CODE) buttons in the HOME
menu.
If DETECT STOP is set to “ON”, “D-STOP” appears at
the side of the cassette indication, as shown in the
following figure.
s
To detect stop codes: [F2], [F3]
When playing a tape on which stop codes are recorded,
you can select four different operation modes, according to
the settings of the [F2] (DETECT BEEP) button and [F3]
(DETECT STOP) button, as follows.
The tape transport modes and speed ranges in which stop
codes can be detected are as follows.
In VAR mode, stop codes cannot be detected at ±0.03
times normal speed.
Adjusting the stop position when a stop
code is detected: [F4]
When a stop code is detected, you can adjust the position
at which the tape transport stops in the direction from the
normal stop position toward the SOM point, within the
range of 0 to 150 frames, in frame units.
1
Press the HOME button.
The HOME menu screen appears.
Note
[F2] (DETECT
BEEP) button [F3] (DETECT
STOP) button VTR operation when stop
code is detected
OFF OFF No operation
L T C
T C R
I N T R P D F F 2
T A P E L O C K
D E T E C T
B E E P
o f f
D E T E C T
S T O P
o f f
D E T E C T
A D J U S T
o f f
R E C
A D J U S T
o f f
C O D E
R E C
o f f
C O D E
E R A S E
o f f
E X I T
00
H
02
M
39
S
18
F
U B 0 0 0 0 0 0 0 0
L T C
T C R
I N T R P D F F 2
T A P E L O C K
D E T E C T
B E E P
o f f
D E T E C T
S T O P
o f f
D E T E C T
A D J U S T
o f f
R E C
A D J U S T
o f f
C O D E
R E C
o f f
C O D E
E R A S E
o f f
E X I T
00
H
02
M
39
S
18
F
U B 0 0 0 0 0 0 0 0
S T I L L
S E T 0 1 3 0 0 0 0 0
D-STOP
S S
H D C A M - S R
R E M A I N : 0 1 H 0 6 M
! T C
D-STOP
OFF ON Stops (for NORMAL PLAY
only)
ON OFF A beeper sounds for 1
second
ON ON Stops (for NORMAL PLAY
only) and simultaneously a
beeper sounds for 1
second
Transport mode
and speed Detected Beeper
timing Stop timing
NORMAL PLAY Yes When read
three times Set by [F4]
(DETECT
ADJUST)
VAR, SHUTTLE
(0 to less than ±8
times normal
speed) Yes When read
twice No operation
REC, EDIT, JOG,
CUE UP,
PREROLL,
SHUTTLE (±8
times normal
speed or more) No No
operation No operation
Note
[F2] (DETECT
BEEP) button [F3] (DETECT
STOP) button VTR operation when stop
code is detected
2 3,5 4
1