Integra DTR-7 - Manual (Page 47)

47
Enjoying Music and Movies in the Sub-room
To control the system in the sub-room
1. Press the POWER ON button on the remote controller.
The MULTI SOURCE indicator located below the STNDBY/
ON button on the receiver will light to indicate that the system
enters the Multi-Source mode.
Note:
If you operate the system in the sub-room while a recording is going on in
the main-room, the source of the recording switches to the source which you
are playing in the main room. Be careful when you are recording a different
source from the one that you are playing.
2. Press the appropiate Input Selector button on the remote
controller to select your desired source and start operating
it.
3. Adjust the volume on the power amplifier to the desired
level.
To control the system using the main unit
(e.g. when no remote controller is available):
1. Press the REC OUT/MULTI SOURCE button on the system
to make sure the MULTI SOURCE indicator flashes in the
display window.
2. Making sure that the indicator flashes, select a source by us-
ing the Smart Scan Controller.
Adjust the volume in the sub-room.
Notes:
• In the sub-room, you can only play the source in the 2-Channel mode.
You cannot play the source in the Multi-Channel mode or the Surround
mode.
• If you press the REC OUT/MULTI SOURCE button in the main room
while you are playing the source in the Multi Source mode in the sub-
room, the Multi Source function will be deactivated and the source will
be inaudible in the sub-room.
• Please note that some third-party multi-room system components may
not be fully compatible with the Onkyo multi-room system components.
1. POWER ON
MASTER VOLUME
STANDBY/ON
PHONES
VIDEO S VIDEO
POWER
OFF ON
A SPEAKERS B
FM AM PHONO C D TAPE VIDEO-1 DVD VIDEO-4 VIDEO-3 VIDEO-2
D O W N U P
FM MUTE/ MODE CHARACTER/ MEMORY SP/SYS
SETUP
MODE
AUDIO ADJUSTMENT BASS/ TREBLE
DISPLAY DSP
PRESET/MODE ADJ
PUSH TO ENTER
DOWN TUNING UP
THX /DTS
SURROUND MODE
LISTENING MODE
STEREO DIRECT DIGITAL/
ANALOG CH LEVEL
DIMMER
REC OUT / MULTI SOURCE
TI CH MUL INPUT
ANDBY ST TI SOURCE MUL
DTR - 7 by
VIDEO4 (MONO)
AUDIO L R
MULTI SOURCE
2. Input Selector
REC OUT/MULTI SOURCE
MULTI SOURCE indicator SMART SCAN Controller
When the system is mounted in a rack:
R V L R L
R L
R L
VIDEO-1
OUT
IN
VIDEO-2
VIDEO-3
OUT
IN
IN
TAPE
VIDEO S VIDEO
OSD SELECTOR
(REC) OUT
IN (PLAY)
DIGITAL OUTPUT
DIGITAL INPUT
COAXIAL 1
COAXIAL 2
OPTICAL 1
OPTICAL 2
OPTICAL
FRONT
FRONT
CENTER
SUB WOOFER
SURROUND
FRONT
CENTER
CD
PHONO
SUB WOOFER
SURROUND
AMP IN
PRE OUT
GND
MONITOR OUT
S
REMOTE
CONTROL REMOTE LOCAL
IN DVD
L R L R
L R
SURROUND SPEAKERS FRONT SPEAKERS A
CENTER SPEAKER
FRONT SPEAKERS B
MULTI CHANNEL
INPUT
MULTI SOURCE OUT
R L
AV RECEIVER
CAUTION: SPEAKER IMPEDANCE 6 OHMS MIN. / SPEAKER
ANTENNA
AM
FM 75
AC INLET
AC OUTLETS AC 120V 60Hz SWITCHED TOTAL 120W 1A MAX. MODEL NO. DTR-7
REMOTE LOCAL
Mini Plug cable
HB-100
Connecting block
120V AC
(unswitched)
Power
supply
Remote sensor HR-600 Remote contoroller
DTR-7/DTR-6
1
2
To enable remote operation when the receiver is mounted in a rack
which will not permit infrared beams to pass, install the remote sen-
sor at a location outside of the rack where the infrared beams from
the controller can reach.
1. Connect the LOCAL jack (on the rear of the receiver) to the
connecting block.
2. Install the remote sensor at a location where it can detect the
infrared beams from the remote controller. Then, connect
the remote sensor to the connecting block.
In the rack Outside of the rack