Insignia N/A NS-BRDVD3-CA - Manual (Page 17)

13
Blu-Ray Disc Player
www.insigniaproducts.com
Selecting the PCM downsampling rate
If your player is connected to an audio receiver or
TV with an optical or coaxial cable, you will need to
select the highest PCM sampling rate the amplifier
supports.
To select the PCM downsampling rate:
1 Press ENTER. The Settings menu opens.
2 Press , press or to select Audio. The Audio
menu opens.
3 Press to select PCM Downsampling, then
press ENTER.
4 Press one or more times to select the PCM
downsampling rate you want. You can select
48KHz, 96KHz, or Off.
If you do not have a surround sound receiver
connected to your player through one of the
digital audio jacks (optical or coaxial), select
48kHz. Otherwise, select the highest sampling
rate the receiver supports. See the
documentation that came with the receiver.
5 Press to go to the previous menu.
Selecting the digital audio output mode
To select the digital audio output mode:
1 Press ENTER. The Settings menu opens.
2 Press or to select Audio. The Audio menu
opens.
3 Press , press or to select Digital Output,
then press ENTER.
4 Press or to select the digital output mode
you want, then press ENTER. You can select:
• PCM—Sends a PCM audio signal of up to 7.1
channels over the HDMI connection and up to
5.1 channels over the coaxial or optical
connection.
• Bitstream HD—Lets your player send Dolby
TrueHD or DTS-MA bitstreams over HDMI (if
your player is connected to a compatible
HDMI audio receiver). If your player is not
connected to a compatible HDMI receiver (for
example, your player is connected directly to
the TV or your player is connected to an audio
receiver using an optical or coaxial cable), a
compatible audio signal is automatically sent
over the HDMI and optical or coaxial
connections.
With this setting, Blu-ray audio is limited to the
soundtrack for the main movie (no PIP audio).
• Bitstream Legacy—Sends a DTS or Dolby
Digital bitstream from the disc over the HDMI
and optical or coaxial connections. Blu-ray
audio is limited to the soundtrack for the main
movie (no PIP audio).
• Bitstream mixed—Sends a mixed (PIP audio
and movie audio) DTS audio stream over the
HDMI and coaxial or optical connections. This
mode is primarily intended for use when you
want to hear both PIP audio and the movie
audio.
5 Press to go to the previous menu.
Turning dynamic range control on or off
Dynamic range control is only active when a Dolby
Digital signal is detected.
When Dynamic Range Control is set to Off, movie
soundtracks are played with the standard dynamic
range.
When movie soundtracks are played at low volume
or from smaller speakers, you can set Dynamic
Range Control to On. Your player applies
appropriate compression to make low-level content
more intelligible and prevent dramatic passages
from getting too loud.
To turn dynamic range control on or off:
1 Press ENTER. The Settings menu opens.
2 Press or to select Audio. The Audio menu
opens.
3 Press , press or to select Dynamic Range
Control, then press ENTER.
4 Press or to select On or Off.
5 Press to go to the previous menu.
Note
Setting the optical or coaxial audio output’s PCM
downsampling sampling rate too high may result in
unpredictable audio playback. If you are not sure, set
the rate to 48kHz.
Settings
Au dio
PCM Downsamp ling
Digital Output
Dynamic Range Contro l
48 K hz
PCM
Off
Language
Audio
Network
System
Display
Parental
Settings
Au dio
PCM Downsamp ling
Digital Output
Dynamic Range Contro l
48 K hz
PCM
Off
Language
Audio
Network
System
Display
Parental
Settings
Au dio
PCM Downsamp ling
Digital Output
Dynamic Range Contro l
48 K hz
PCM
Off
Language
Audio
Network
System
Display
Parental
NS-BRDVD3-CA_11-0646_MAN_V6_English.book Page 13 Tuesday, June 21, 2011 4:29 PM