I-O Display Systems Basic I/O Product - Manual (Page 14)

The Basic I/O 1
1-9(Vol.1)
Available I/O Modules
ANALOG INPUTS, 12 BIT ANALOG OUTPUTS, 12 BIT
Frequency Voltage
IIF10K-B Input 300Hz -10KHz OV1 Output 0-1V, self-sourcing
IF2.5K-L Input 0-2.5KHz OV5 Output 0-5V, self-sourcing
IF5K-l Input 0-5KHz OV10 Output 0-10V, self-sourcing
IF10K-L Input 0-10KHz
Voltage Current
IV25M Input 0-25mV OI420 Output 4-20mA, self-sourcing To 275 Ohm
load.
IV50M Input 0-50mV
IV100M Input 0-100mV
IV1 Input 0-1V DIGITAL INPUTS
IV5 Input 0-5V AC
IV5B Input Bipolar +/-5V IAC5 Input 90-140Vac
IV10 Input 0-10V IAC5A Input 180-280Vac
IV10B Input Bipolar +/-10V DC
IVAC Input 28-140Vac IDC5D Input 3-32Vdc Fast, >500Hz
IVAC-A Input 56-280Vac IDC5S* Input Dry Contact Sense Built-in Isolated
Voltage Source
Current IDC5NP Input 10-32 Vdc, 15-32Vac Non-Polarized
II420 Input 4-20mAdc
IIAC5 Input 0-5Aac
Thermocouple DIGITAL OUTPUTS
ITCE Type E 0 To 435 C AC
ITCJ Type J 0 To 700 C OAC5 Output 12-140Vac, 3.5A
ITCJ-1 Type J -80 To 750 C OAC5A Output 24-280Vac, N.C.(Normally Closed)
ITCK Type K -100 To 924 C OAC5J Output 20-280Vac, 6.0A
ITCK-1 Type K -110 To 1250 C
ITCR Type R 0 To 960 C DC
ITCR-1 Type R 0 To 1760 C ODC5 Output 5-60Vdc, 3.5A
ITCS Type S 0 To 1034 C ODC5A Output 4-200Vdc, 1.0A
ITCS-1 Type S 0 To 1760 C ODC5R Electro-Mechanical 0.5A Relay Form A,
Normally Open (NO)
ITCT Type T -200 To 224 C
I TCT-1 Type T -120 To 400 C SPECIAL PURPOSE
ITCT-2 Type T 0 To 150 C IDC5Z* Input +/-200mV, 0-10KHz Digital**
RTD SPS-1* Sensor Power Supply 18-24 Vdc, 30mA
ITR10 10 Ohm Cu -55 To 150 C
TI01 Digital Input/ Output Test Module with Field
Switch and LED
ITR100 100 Ohm Pt -55 To 350 C SUPPORT PRODUCTS
ITR100-1 100 Ohm Pt 0 To 100 C Fuses
Type 590 Temperature Sensor FM-06 Fuse Assembly 0.062A
ITP590 -188.4 To 150 C FM-1 Fuse assembly, 1.0A
ITP590-1 -50.0 To 150 C FM-3 Fuse assembly , 3.0A
FM-5 Fuse assembly, 5.0A
* When selecting a power supply for the system assume 25mA for standard digital modules and 100 mA
for marked with an *** The IDC5Z module is used for low-level signals and will pass signals at the rate
of 10KHz The BASIC I/O however, is limited to signals up to 500Hz.