Marantz SR7500 - Manual (Page 21)

17
ENGLISH
AC IN
MULTI
OUT
TV DVD
C
IN OUT
S-VIDEO
DVD DSS/VCR2
C
RS-232C
MULTI RC
IN OUT DSS/VCR2 IN OUT OUT VCR1
VCR1
L
SBR
SBL
OUT PRE
SL L
SR R
DSS/VCR2 DVD TV
R
IN
R SW
RC-5 IN
SR
AUDIO
7.1CH IN
OUT IN
L SL
SBR
SBL CD
IN OUT SW OUT
CDR/MD TAPE
OUT IN
IN OUT
VIDEO
MONITOR OUT MULTI VCR1 TV OUT
(AUX2)
MONITOR
DIGITAL IN DIGITAL OUT
4
1 OPT. 2
5
3
6 COAX.
R L R R
FRONT A
L L
FM (75½)
ANTENNA
GND AM
COMPONENT VIDEO
CB/PB CR/PR CR/PR CR/PR CB/PB CB/PB TV Y Y
MONITOR OUT
VCR1
DVD DSS/VCR2
Y
SURROUND
100W MAX.
AC OUTLET
SWITCHED 230V 50/60H Z
OUT
SPEAKER SYSTEMS FRONT A OR B, CENTER, SURR, SURR BACK : 6 - 8 OHMS FRONT A + B : 8 OHMS
FLASHER IN
DC OUT 1 2
1 2
R L
FRONT B CENTER
SURROUND BACK/ MULTI SPEAKER/ SPEAKER C
ON
OFF SPEAKER C
OUTPUT INPUT-2 INPUT-1 DVI-D
R L
SURROUND BACK/ MULTI SPEAKER/ SPEAKER C
ON
OFF SPEAKER C
MULTI
OUT
MULTI RC IN
OUT
OUT MULTI
AUDIO
RC-5
L R
L
R
FRONT RC IN
R L
RC OUT
IN
VIDEO
CONNECTING FOR THE MULTI ROOM
RIGHT
SPEAKER
LEFT
SPEAKER
IR RECEIVER
MULTIROOM
RIGHT
SPEAKER
MULTIROOM
LEFT
SPEAKER
MAIN AMP
(For MULTIROOM)
MULTIROOM
(Multi room speaker)
MONITOR
AC IN
MULTI
OUT
C
IN OUT
S-VIDEO
DVD DSS/VCR2
C MULTI RC
SBR
SBL
OUT PRE
SL L
SR R
R SW
IN
SR
7.1CH IN
IN
L SL
SBR
SBL
OUT SW OUT
CDR/MD E
IN OUT VCR1 TV OUT
(AUX2)
MONITOR
R L R R
FRONT A
L L
COMPONENT VIDEO
CR/PR CR/PR CR/PR CB/PB CB/PB Y
MONITOR OUT
VCR1
DSS/VCR2
Y
SURROUND
100W MAX.
AC OUTLET
SWITCHED 230V 50/60HZ
OUT
SPEAKER SYSTEMS FRONT A OR B, CENTER, SURR, SURR BACK : 6 - 8 OHMS FRONT A + B : 8 OHMS
FLASHER IN
DC OUT 1 2
1 2
R L
FRONT B CENTER
SURROUND BACK/ MULTI SPEAKER/ SPEAKER C
ON
OFF SPEAKER C
OUTPUT INPUT-2 DVI-D
R L
SURROUND BACK/ MULTI SPEAKER/ SPEAKER C
ON
OFF SPEAKER C
R
FRONT A
L
ON
OFF
SPEAKER C
Note:
• You can use surround back speaker terminals as
multi room speaker terminals or speaker C
terminal when you use no surround back speaker.
CONNECTING FOR SPEAKER C USE
Bi-wire Connection
A bi-wire connection is possible with speakers that
have two sets of inputs (for treble and bass).
This allows you to drive the treble and bass units
with separate channel amps, which enables better
sound quality. Connect the speakers as shown in
the figure. Set the SPEAKER C selector switch on
the rear panel to ON.
Notes:
• If incorrectly connected, a protective circuit in the
receiver will trip and set the receiver to standby.
(The STANDBY indicator will flash.) In such
case, recheck the connections between the
speakers and the receiver.
• Turn power to the receiver off before changing the
setting of the SPEAKER C selector switch.