Hustler Turf Mini Fastrack - Manual (Page 26)

24 601156_1106
Mini FasTrak 36/42
Maintenance Schedule
Refer to Fig. 4-12
SERVICE AT
INTERVALS INDICATED
WEEKLY
OR 50
HOURS
ANNUALLY
OR 100
HOURS
Verify safety start interlock system Prior to each use
Visually inspect unit for loose
hardware and/or damaged parts
Prior to each use
Visually inspect tires Prior to each use
Check oil level, engine (1) Prior to each use or every 4 hours
Clean air intake screen (4) Prior to each use or every 4 hours
Clean foam element (4) Prior to each use or every 4 hours
Check fuel level Prior to each use
Blades - sharpen & securely fastened Prior to each use
Discharge chute - securely in place &
in lowest position
Prior to each use
Clean engine and transaxle
compartment
Daily
Grease deck height pivots X
Grease gauge wheel bearings X
Change engine oil and filter (1) (3) X
Clean cylinder and head fins(a) X
Check battery connections X
Check tire pressure with a gauge X
Clean engine exterior (a) X
Replace air cleaner paper element (4) X
Clean & regap spark plugs (a) X
Check pump and deck belt tension
and condition (5)
X
Check fuel and hydraulic lines (6) X
Check fuel valve and grommet (6) X
Tighten lug nuts on wheels (2) X
Change fuel filter X
Replace spark plugs X
NOTES:
1. Initial oil change is after 5 hours of operation. Thereafter, change oil after
every 40 hours operation. Change more often under dusty or dirty condi-
tions and during hot weather periods.
2. Torque initially and after first 2 hours of operation.
3. Change engine oil filter per the engine manufacturer’s recommendations.
Refer to Engine Owner’s Manual for recommendations and other mainte-
nance items.
4. Service more often under dusty or dirty conditions.
5. Pump drive belt only - Inspect every 6 months or 100 hours and replace
if worn or cracking is noticed. Otherwise, replace every 200 hours or 2
years whichever comes first.
6. Check fuel line hoses, fuel valve and grommets for any cracks or leaks
REFERENCES:
a — Refer to Engine Owner’s Manual
NOTE: After completing maintenance cycle (100 hours), repeat cycle.
FasTrak 48/54
Maintenance Schedule
Refer to Fig. 4-13
SERVICE AT
INTERVALS INDICATED
WEEKLY
OR 50
HOURS
MONTHLY
OR 100
HOURS
ANNUALLY
OR 300
HOURS
Verify safety start interlock system Prior to each use
Visually inspect unit for loose
hardware and/or damaged parts
Prior to each use
Visually inspect tires Prior to each use
Check oil level, engine (1) Prior to each use or every 4 hours
Clean air intake screen (4) Prior to each use or every 4 hours
Clean foam element (4) Prior to each use or every 4 hours
Check fuel level Prior to each use
Blades - sharpen & securely fastened Prior to each use
Discharge chute - securely in place &
in lowest position
Prior to each use
Clean engine and transaxle
compartment
Daily
Change transaxle oil and filter (7) Every 200 hours or 2 years
Grease deck height pivots X
Grease gauge wheel bearings X
Change engine oil and filter (1) (3) X
Clean cylinder and head fins(a) X
Check battery connections X
Check tire pressure with a gauge X
Check hydraulic oil level X
Clean engine exterior (a) X
Clean & regap spark plugs (a) X
Check pump and deck belt tension
and condition (5)
X
Check fuel and hydraulic lines (6) X
Check fuel valve and grommet (6) X
Tighten lug nuts on wheels (2) X
Change fuel filter X
Replace spark plugs X
NOTES:
1. Initial oil change is after 5 hours of operation. Thereafter, change oil after
every 40 hours operation. Change more often under dusty or dirty condi-
tions and during hot weather periods.
2. Torque initially and after first 2 hours of operation.
3. Change engine oil filter per the engine manufacturer’s recommendations.
Refer to Engine Owner’s Manual for recommendations and other mainte-
nance items.
4. Service more often under dusty or dirty conditions.
5. Pump drive belt only - Inspect every 6 months or 100 hours and replace
if worn or cracking is noticed. Otherwise, replace every 200 hours or 2
years whichever comes first.
6. Check fuel line hoses, fuel valve and grommets for any cracks or leaks
7. Initial system oil and filter change must be after the first 75 hours of use or
1 year whichever comes first. Thereafter, replace filter and oil in each
transaxle every 2 years or 200 hours, whichever comes first.
REFERENCES:
a — Refer to Engine Owner’s Manual
NOTE: After completing maintenance cycle (300 hours), repeat cycle.