Honeywell ADEMCO 5828V - Manual

K0021 3/03 Rev. B
$'(0&29
:LUHOHVV%LGLUHFWLRQDO)L[HG:RUG.H\SDG
USER GUIDE
GENERAL INFORMATION
The 5828 and 5828V are wireless keypads that can be
used to operate and get status from your security
system. The 5828 and 5828V have the following
features (voice annunciation features apply only to the
5828V):
N Can be used to arm/disarm, and perform other
system operations.
N Can display and/or annunciate system status.
N Can automatically display and/or annunciate a
change in system status if AC powered (e.g., for an
alarm, the keypad will announce the type of alarm
(fire or burglary) and location (e.g. kitchen window).
N Message Center can be used to record and play back
a voice memo to yourself, or leave a message for a
family member.
N Can be battery- or AC-powered (AC-powered units
have several advantages, described below).
Battery-Powered Operation: :KHQ SRZHUHG E\
EDWWHU\ WKH NH\SDG PXVW ILUVW EH DFWLYDWHG E\ SUHVVLQJ
DQ\ QXPEHUHG NH\ 7KH NH\SDG ZLOO GLVSOD\ WKH FXUUHQW
V\VWHP VWDWXV ZLWKLQ D IHZ VHFRQGV
WLPH EHIRUH RU DIWHU UHFHLYLQJ VWDWXV DUP GLVDUP VHQG
D SDQLF DODUP RU SHUIRUP RWKHU V\VWHP RSHUDWLRQV 7KH
NH\SDG EHFRPHV LQDFWLYH ZKHQ QR NH\V KDYH EHHQ
SUHVVHG IRU VHFRQGV DQG PXVW EH UHDFWLYDWHG WKH
QH[W WLPH \RX ZDQW WR XVH LW
AC-Powered Operation:
:KHQ SRZHUHG E\ WKH
RSWLRQDO $& DGDSWHU WKH NH\SDG UHPDLQV DFWLYH DW DOO
WLPHV RQ /\Q[5 V\VWHPV ZKHQ WKH V\VWHP LV
GLVDUPHG WKH YLVXDO GLVSOD\ ZLOO WXUQ RII DIWHU
VHFRQGV LI WKHUH LV QR DFWLYLW\ DW WKH NH\SDG RQ /\Q[
5(1 V\VWHPV WKH GLVSOD\ UHPDLQV RQ $Q\ FKDQJH LQ
V\VWHP VWDWXV ZLOO FDXVH WKH GLVSOD\ WR DXWRPDWLFDOO\
WXUQ RQ LI EODQN DQG GLVSOD\DQQXQFLDWH WKH QHZ
VWDWXV ,I $& SRZHU LV ORVW WKH NH\SDG UHYHUWV WR
EDWWHU\SRZHUHG RSHUDWLRQ XQWLO $& SRZHU LV UHVWRUHG
DQG D QHZ VWDWXV UHTXHVW LV PDGH ✱ key
NOTE:
:KHWKHU WKH XQLW LV SRZHUHG E\ EDWWHU\ RU $&
WKH 9 PD\ WDNH D IHZ VHFRQGV WR GLVSOD\
DQGRU DQQXQFLDWH WKH QHZ VWDWXV DIWHU SUHVVLQJ WKH [✱]
NH\
5828V
-00-002-V0
1
OFF
4
MAX
7
INSTANT
READY
2
AWAY
5
TEST
8
CODE
0
3
STAY
6
BYPASS
9
CHIME
#
MESSAGE
MIC
ARMED
READY
RECORD VOLUME PLAY
STATUS FUNCTION VOICE
D
C
B
A
5828V Keypad with Front Cover Removed
KEYPAD KEYS
These keypads include 12-operational keys, as well as
four Special Function keys that are backlit for ease of
use when the keypad is active. To access the keypad
keys, simply open the swing-down door by applying
outward pressure on the door release slot on the right
side.
Panic alarms are activated by pressing the key pairs
shown in the table below. Special Function keys A, B,
and C, can be programmed by your installer to provide
the same alarms by pressing a single key and holding it
down for 3-seconds, or can be assigned other system
operations. (Check with your installer for the
availability and assignment of these keys).
Panic Alarm Key-
Pairs/Special Function Keys
[1] & [ ✱] or A
[ ✱] & [#] or B
[3] & [#] or C
SOUNDER
The keypad’s built-in sounder pulses for fire alarms,
and sounds continuously for burglary and audible
panic alarms.
HOW TO GET SYSTEM STATUS
Turn on the keypad by pressing any numbered key.
Status will be displayed within a few seconds.
Additionally, on AC powered units, the keypad is
automatically updated when a change in system status
takes place (arming, disarming, trouble, etc.).
HOW TO PROGRAM OR CHANGE YOUR 4-DIGIT
SECURITY CODE
In order to Quick Arm the system using this keypad,
you will need to program your own 4-digit security code
into the keypad. This code must match a code that has
already been programmed into your control panel. To
program the 4-digit code, perform the following steps:
Press the 7 INSTANT and 9 CHIME keys at the
same time until the display flashes double dashes
(- -), then release.
Enter the 4-digit security code that matches a valid
user code already programmed into your control
panel. Do NOT use the Duress Code. There will be
no display of the numbers you pressed.
Press ✱ READY to accept your entry. The keypad
will display the system status.