Harbor Freight Tools 67596 - Manual (Page 3)

Page 3 For Pressure Washer technical questions, please call 1-800-444-3353. SKU 67546/67596
For engine technical questions, please call 1-800-520-0882.
Specifications
Displacement 212cc
Engine Type Predator OHV
Pump Brass Axial
Drive Direct
Gun 22 IN. Wand / 20 IN. Lance
Nozzles
Quick Connect 0º, 15º, 25º, 40º
+ Soap Nozzle
Hose Length 26 FT. 7 IN.
Cart
Push type with 10 IN.
Pneumatic tires
Fuel
Type 87+ octane unleaded gasoline
Capacity 1 Gallon / 3.6L
Engine
Oil
(not
included)
Type
(SAE)
10W-30 above 32° F
5W-30 at 32° F or below
Capacity 0.5 Quart / 0.5L
Low Oil
Shutdown Yes
Pump Oil
(included)
3.75 fl-oz SAE 10W-30
Non-detergent
Engine Speed 3,600 RPM
Water Flow 3 GPM Maximum
Maximum Pressure 2,500 PSI
Bore x Stroke 70 mm x 55 mm
Compression Ratio 8.5:1
Rotation viewed from
PTO (power takeoff
- the output shaft)
Counterclockwise
Spark Plug
Type
NGK ® BP-6ES
NHSP ® / Torch ® F6TC
Gap 0.7 - 0.8 mm
Valve Clearance
Intake 0.10 - 0.15 mm
Exhaust 0.15 - 0.20 mm
item 67546: The emission control system
for this Pressure Washer’s engine is warranted
for standards set by the U.S. Environmental
Protection Agency. For warranty information,
refer to the last pages of this manual.
item 67596: The emission control system
for this Pressure Washer’s Engine is warranted for
standards set by the U.S. Environmental Protection
Agency and by the California Air Resources Board
(also known as CARB). For warranty information,
refer to the last pages of this manual.
At high altitudes, the engine’s carburetor,
governor (if so equipped), and any other parts that
control the fuel-air ratio will need to be adjusted
by a qualified mechanic to allow efficient high-
altitude use and to prevent damage to the engine
and any other devices used with this product.
Save this manual
Keep this manual for the safety warnings and
precautions, assembly, operating, inspection, maintenance
and cleaning procedures. Write the product’s serial number
in the back of the manual near the assembly diagram (or
month and year of purchase if product has no number).
Keep this manual and the receipt in a safe and dry place
for future reference.
Safety Warnings
i n this manual, on the labeling, and all other
information provided with this product:
this is the safety alert symbol. it is
used to alert you to potential personal
injury hazards. Obey all safety
messages that follow this symbol
to avoid possible injury or death.
DanGeR
DanGeR indicates a hazardous situation which, if
not avoided, will result in death or serious injury.
WaRninG
WaRninG indicates a hazardous situation which, if
not avoided, could result in death or serious injury.
CautiOn
CautiOn, used with the safety alert symbol,
indicates a hazardous situation which, if not
avoided, could result in minor or moderate injury.
Notice
nOtiCe is used to address practices
not related to personal injury.
CautiOn
CautiOn, without the safety alert symbol, is used
to address practices not related to personal injury.
WaRninG! Read all instructions.
Failure to follow all instructions listed below
may result in fire, serious injury and/or
Death.
The warnings and precautions discussed in this
manual cannot cover all possible conditions and
situations that may occur. It must be understood
by the operator that common sense and caution
are factors which cannot be built into this
product, but must be supplied by the operator.
Save theSe inStRuCtiOnS.
Rev 11c