Specifications, Save this manual, Safety warnings and precautions – Harbor Freight Tools 94076 User Manual
Page 2
Page 2
SKU 94076
For technical questions, please call 1-800-444-3353.
Specifications
d
e
e
p
S
l
o
o
T
)
d
a
o
l
o
n
(
M
P
R
0
5
2
,
6
1
y
l
p
p
u
S
r
e
w
o
P
z
H
0
6
,
C
A
V
0
2
1
:
t
u
p
n
I
A
m
0
0
5
,
C
D
V
2
1
:
t
u
p
t
u
O
L
U
®
r
e
t
p
a
d
A
r
e
w
o
P
d
e
t
s
i
L
s
e
z
i
S
t
e
ll
o
C
”
4
6
/
3
,
”
2
3
/
3
,
”
8
/
1
d
a
e
r
h
T
e
l
d
n
i
p
S
5
7
.
x
8
M
Accessories listed on page 8 on the accessory list.
Save This Manual
You will need the manual for the safety warnings and precautions, assembly instructions, operating and mainte-
nance procedures, parts list and diagram. Keep your invoice with this manual. Write the invoice number on the
inside of the front cover. Keep the manual and invoice in a safe and dry place for future reference.
Safety Warnings and Precautions
WARNING: When using tool, basic safety precautions should always be followed to reduce the risk of
personal injury and damage to equipment.
Read all instructions before using this tool!
1.
Keep work area clean. Cluttered areas invite injuries.
2.
Observe work area conditions. Do not use machines or power tools in damp or wet locations. Don’t expose
to rain. Keep work area well lighted. Do not use electrically powered tools in the presence of flammable gases
or liquids.
3.
Keep children away. Children must never be allowed in the work area. Do not let them handle machines,
tools, or extension cords.
4.
Store idle equipment. When not in use, tools must be stored in a dry location to inhibit rust. Always lock up
tools and keep out of reach of children.
5.
Use the right tool for the job. Do not attempt to force a small tool or attachment to do the work of a larger
industrial tool. There are certain applications for which this tool was designed. It will do the job better and
more safely at the rate for which it was intended. Do not modify this tool and do not use this tool for a purpose
for which it was not intended.
6.
Dress properly. Do not wear loose clothing or jewelry as they can be caught in moving parts. Protective,
electrically nonconductive clothes and nonskid footwear are recommended when working. Wear restrictive
hair covering to contain long hair.
7.
Use eye and ear protection. Always wear ANSI approved impact safety goggles. Wear a full face shield if
you are producing metal filings or wood chips. Wear an ANSI approved dust mask or respirator when working
around metal, wood, and chemical dusts and mists.
8.
Do not overreach. Keep proper footing and balance at all times. Do not reach over or across running
machines.
9.
Maintain tools with care. Keep tool and accessories sharp and clean for better and safer performance.
Follow instructions for lubricating and changing accessories. Inspect tool cords periodically; and if damaged,
have them repaired by an authorized technician. The handle must be kept clean, dry, and free from oil and
grease at all times.
10. Disconnect power. Unplug adapter when not in use.
11. Remove adjusting keys and wrenches. Check that keys and adjusting wrenches are removed from the tool
or machine work surface before plugging it in.
12. Avoid unintentional starting. Be sure the switch is in the Off position when not in use and before plugging
in. Do not carry any tool with your finger on the switch, whether it is plugged in or not.