Hobart Welding Products POWERPAK OM-478 User Manual
Page 56
OM-478 Page 52
11-2. Approximate Air Consumption (Cubic Feet) To Operate Pneumatic Equipment At
70-90 P.S.I.G.
Drill, 1/18” to 3/8”
3.75
6.25
8.75
25
Burring Tool, Large
3.6
6.0
8.4
24
Drill, 3/8” to 5/16”
5.25
8.75
12.25
35
Rammers, Small
3.9
3.25
9.1
13
Screwdriver,
#2 to #6 Screw
1.8
3.0
4.2
12
Rammers, Medium
5.1
8.5
11.9
34
Screwdriver,
#6 to 5/16” Screw
3.6
6.0
8.4
24
Rammers, Large
6.0
10.0
14.0
40
Tapper, to 3/8”
3.0
5.0
7.0
20
Backfill Tamper
3.75
6.25
8.75
25
Nutsetters, to 3/8”
3.6
6.0
8.4
24
Compression Riveter
0.2 cu. ft. per cycle
Nutsetters, to 3/4”
4.5
7.5
10.5
30
Air Motor,
1 Horsepower
3.75
6.3
8.75
25
Impact Wrench, 1/4”
2.25
3.75
5.3
15
Air Motor,
2 Horsepower
7.5
12.5
17.5
50
Impact Wrench, 3/8”
3.0
5.0
7.0
20
Air Motor,
3 Horsepower
11.25
18.75
26.3
75
Impact Wrench, 5/8”
4.5
7.5
10.5
30
Air Motor Hoist
Impact Wrench, 3/4”
5.25
8.75
12.25
35
1000#
1 cu. ft. per foot of lift
Impact Wrench, 1”
6.75
11.25
15.75
45
Air Motor Hoist,
2000#
1 cu. ft. per foot of lift
Impact Wrench, 1-1/4”
8.25
13.75
19.2
55
Paint Spray Gun
Die Grinder, Small
2.25
3.75
5.3
15
(Production)
3.0
5.00
7.00
20
Die Grinder, Medium
3.6
6.0
8.4
24
HAMMERS
Horizontal Grinder, 2”
3.0
5.0
7.0
20
Scaling Hammer
1.3
3.0
4.2
12
Horizontal Grinder, 4”
9.0
15.0
21.0
60
Chipping Hammer
4.5
7.5
10.5
30
Horizontal Grinder, 6”
9.0
15.0
21.0
60
Riveting Hammer,
Light
2.25
3.75
5.25
15
Horizontal Grinder, 8”
12.0
20.0
28.0
80
Riveting Hammer,
Heavy
4.5
7.5
10.5
30
Vertical Grinders and
Sanders, 5” Pad
5.25
8.75
12.25
35
SAWS
Vertical Grinders and
Circular, 8”
6.75
11.25
15.75
45
Sanders, 7” Pad
9.0
15.0
21.0
60
Circular, 12”
9.75
16.25
23.8
65
Vertical Grinders and
Sanders, 9” Pad
10.5
17.5
24.5
70
Chain, Lightweight
4.20
7.0
9.8
28
Burring Toll, Small
2.25
3.75
5.3
15
Chain, Heavy Duty
13.1
21.8
30.5
87
MISCELLANEOUS
PORTABLE
TOOLS
Percent Use Factor And
Compressed Air Consumption (CF)
MISCELLANEOUS
PORTABLE
TOOLS
Percent Use Factor And
Compressed Air Consumption (CF)
9 sec
15 sec
21 sec
1 min
9 sec
15 sec
21 sec
1 min
Always check with tool manufacturers for actual air consumption of tools being used. The above is based on averages and should not be
considered accurate for any particular make of tool.
Above tools are rated based upon typical “on-load” performance characteristics.
For other values, adjust the C.F. air consumption on a proportional basis.
The cubic feet (C.F.) air consumption for 1 minute may also be expressed as air consumption in cubic feet per minute (C.F.M.)