haier XQG50-S1216 - Manual (Page 5)

3. Never place heavy objects, e.g. a heating
appliance or water container, on the top panel
of the washing machine. 4. Do not wash foam rubber or simalar sponge
materials.
5. Before washing, close zippers, buttons,
laces and repair damaged areas. Underwear
and amall items should be palced in a laun-
dry bag or pillow slip. Do not wash clothes
containing wire frames. 6. Do not open the detergent dispenser during
the wash cycle. Otherwise, the water will spilt
out from it and the detergent can not be wash-
ed out completely.
7. The door is fitted with a self-locking device
and can be opend when it is under the safety
state ( water should be under the safe level;
temperature inside the drum should be less
than 55
§; the drum should do not run). Do
not open the door except above condition
otherwise the self-locking device will be
damaged and the operator will get hurt.
8. After washing, turn off the tap to prevent
leaking; unplug the washing machine and
wipe clean the lower part of the porthole.
9. Keep the door slightly open when the wa-
shing machine is not being used. Never cover
the machine a
plastic sheet. 10. The tumble dryer should not be used if
industraial chemicals have been used for
cleaning
11. The appliance must not be installed behind
a lockable door, a sliding door or a door with
a hinge on the opposite to that of the tumble
dryer.
Matters needing attention
The water is above the
warning level
Warning code
Warning
code
Abnorma item Content of identification Action to take
Checking position and
ask for help
E11
E12
E13
E31
EA3
EC1
EC2
EC3
EC4
EC5
U01
U02
U03
U04
E22
Water supply
Drainage
Water supply
Motor
Water level is
abnormal in the
drying process
Heater
Water tempera-
ture sensor
Water level
sensor
The temperature
of air vent
The dry tempe-
rature sensor
Unlock the door
Lock the door
Spin lopsidedly
The memory
function is failure
Unclose the door
Warning and
stop running
Warning and
stop running
Warning and
stop running
Warning and
stop running
No heating and
washing with
cold water
Warning and
stop running
Warning and
stop running
Warning and
stop running
Warning and
stop running
Warning and
stop running
Warning and
stop running
Spin low speed
and cancel
drying
Warning
Warning
Check if the water outlet
of the drainage and
adjust it and restart the
machine
Ask the technician to
repair
Ask the technician to
repair
Ask the technician to
repair
Ask the technician to
repair
Ask the technician to
repair
Ask the technician to
repair
Ask the technician to
repair
Ask the technician to
repair
Ask the technician to
repair
Ask the technician to
repair
Disperse the clothings
evenly in the tube
Check if the water outlet
of the drainage and adjust
it and restart the machine
Close the door
Warning and
stop running
Check if the water
pressure is low or stops
supplying The water level can not
reach the reset water
level within 5 minutes
Warning and
stop running
Check if the water
pressure is low or stops
supplying The water level can not
reach the setting water
level within 8 minutes
The water level can not
reach the reset level in
8 minutes after drainage
starting
The feedback signal do-
es not change in 8 minu-
tes during the motor runs
The water is ablove the
setting water level during
the drying process
The water temperature
unchanged in 10 minutes
The drying sensor circuit
short cut or open
The water level sensor
circuit short cut or open
Within 30 minutes of dry
phase there is 5 minutes
in which the temperature
is not increasing
The heater sensor circuit
short cut or open
Can not unlock after 4
times try
Can not lock the door
after 4 times try
The judgement of un-
balance is above 1000g
EEPROM goes wrong
The door is unclosed
3 14