Hunter Fan 43255 User Manual

Page 6

system

cool

heat

off

fan

auto

Reviewing Programs

To review your program settings, press

program

repeatedly to cycle through the programs.

You can also make changes at any time.

System Selector Switch

The System Selector switch on the front of the thermostat
determines the operating mode of the thermostat. You may
select COOL, OFF, HEAT.

NOTE: Anytime you install or remove the thermostat
from the wallplate, slide the System Selector to the
OFF position to prevent the possibility of a rapid sys-
tem On-Off.

Fan Switch

The Fan switch should normally be located in the AUTO
position. The Fan will be turned on along with normal opera-
tion of your system. In a normal gas or oil furnace, the Fan
will be turned on by your furnace after its warm-up delay. For
electric heat, air conditioning, and heat pump operation, the
Fan will turn on with the system.

To run the Fan on continuously, slide the Fan switch to the ON position.

Temporary Manual Override

To temporarily change the current set temperature without affecting your program:

■ Press and hold for about 1 second

to enter Manual Override mode. When
display flashes, you can release the key.

■ Press again to change to your desired Set

Temperature. Hold the key for 2 seconds to
fast-advance the Set Temperature.

■ Press to return to normal mode, or wait 5

seconds for it to return automatically.

■ The current program number will flash to

signify the Temporary Override.

■ At the next program change time, the Tem-

porary Override is cancelled, and the next
program temperature becomes the setpoint
temperature.

To end the Temporary Manual Override:

■ Press, then press again. This will return the set temperature to the current

program set temperature.

Permanent Override

To hold your Manual Override for vacation or just an extended period of time:

■ Press to make the current program tem-

perature the HOLD temperature. HOLD
will be displayed on the LCD, and the
Program number will disappear.

■ Follow the Temporary Manual Override

instructions above to change the Permanent
Manual Override temperature.

■ You can confirm the held set temperature by

pressing for less than 1 second.

To end the Permanent Manual Override:

■ Press again. The thermostat will return to the current program, and the HOLD

display will be canceled.

SET TEMP

COOL TEMP

hold

/return

hold

/return

hold

/return

HOLD

TEMP

hold

/return

Filter Monitor

Your thermostat measures the number of hours your heating and cooling system has been in
use. To maximize your system’s performance and energy efficiency, change or clean your filter
regularly.

■ When the total system runtime for heat and

cool reaches 400 hours, the Filter Change
Indicator will flash as a reminder to check
your system’s filter.

■ Press to review total filter usage. After 15

seconds, the display will return to normal
mode, or you can press the HOLD / RE-
TURN key to exit immediately.

■ After changing or cleaning the system’s

filter, press and hold the Filter Key for 3
seconds. The display will blink, and the
timer will be reset to zero.

SPAN Setting Mode

Your thermostat is set at the factory to cycle at 1˚F (0.5˚C) above and below the set temperature.
(Span = 2) This setting has been designed to provide a comfortable room temperature under
most all conditions. However, if you find your system cycling too fast or too slow, then the Span
can be adjusted to modify the cycle time.

■ Press and hold BOTH for three seconds. The

display will flash, and SPAN will be dis-
played on the LCD.

■ Press to raise the Span to 3. This setting

INCREASES the cycle time by allowing your
system to run LONGER.

■ Press to lower the Span to 1. This setting

DECREASES the cycle time by causing your
system to run SHORTER.

The Span settings remain the same for both HEAT and COOL.

The Span can be changed at any time, and is independent of program times
or temperatures.

When batteries are installed in the thermostat, or the Reset key is pressed, the Span is reset back
to setting 2.

Backlighting (INDIGLO

Night-Light)

Your thermostat has an electroluminescent lamp that backlights the display for easy viewing in
the dark.

When any key is pressed or the System Switch is changed, the display is illuminated.

The display will remain illuminated for 5 seconds after the last key is pressed. This allows the
light to stay on if you need to operate several keys.

Note: If the thermostat is in Low Battery warning condition, the backlight will not
operate. Replace with 2 new alkaline batteries to restore the Backlight function.

Low Battery Warning

Your thermostat has a two-stage low battery warning system.
When the batteries are first detected to be weak, the first stage
low battery warning is indicated by battery symbol flashing on
the LCD display. At your earliest convenience, you need to
replace the batteries with 2 new AA alkaline batteries.

When the batteries become too weak for normal operation,
the thermostat enters the second stage low battery warning
which shuts down the thermostat. In this condition, “BATT”
flashes alone on the display, and the thermostat will turn
your system Off. Your system will remain shut-off until the
batteries are replaced.

Note: The thermostat will still keep the current time and your programs in memory until
new batteries are installed. After confirming that new batteries have been inserted, the
thermostat will return to normal operation.

filter

TEMP

COOL

M T W

F SA SU

SET TEMP

FILTER

MIN

HEAT

TEMP