Harman-Kardon AVR 120 - Manual (Page 13)

13 REMOTE CONTROL FUNCTIONS
s Tuner Mode: Press this button when the
tuner is in use to select between automatic
tuning and manual tuning. When the button is
pressed so that the AUTO Indicator
R goes
out, pressing the Tuning Buttons u8 will
move the frequency up or down in single-step
increments. When the FM band is in use, press-
ing this button when a station’s signal is weak
will change to monaural reception. (See page
25 for more information.)
t Direct Button: Press this button when
the tuner is in use to start the sequence for
direct entry of a station’s frequency. After press-
ing the button simply press the proper
Numeric Keys
r to select a station. (See
page 25 for more information on the tuner.)
u Tuning Up/Down: When the tuner is in
use, these buttons will tune up or down through
the selected frequency band. If the Tuner Mode
Button
s@ has been pressed so that the
AUTO Indicator R is illuminated, pressing and
holding either of the buttons for three seconds
will cause the tuner to seek the next station with
acceptable signal strength for quality reception.
When the AUTO Indicator
R is NOT illumi-
nated, pressing these buttons will tune stations
in single-step increments. (See page 25 for more
information.)
v Macro Buttons: Press these buttons
to store or recall a “Macro”, which is a
preprogrammed sequence of commands
stored in the remote. (See page 28 for more
information on storing and recalling macros.)
w Transport Controls: These buttons do
not have any functions for the AVR 120, but
they may be programmed for the forward/
reverse play operation of a wide variety of CD
or DVD players, and audio or video cassette
recorders. (See page 30 for more information
on programming the Transport Control Punch-
Through capability of the remote.)
x Skip Up/Down Button: These buttons
have no direct function with the AVR 120, but
when used with a compatibly programmed CD
or DVD changer they will change the disc cur-
rently being played in the changer.
y Disc Skip Button: This button has no
direct function for the AVR 120, but is often
used when the remote is programmed to oper-
ate a CD or DVD changer to change the discs in
the changer. (See page 28 for more information
on using the remote with other devices.)
z Preset Up/Down: When the tuner is
in use, press these buttons to scroll through the
stations programmed into the AVR 120’s mem-
ory. When some source devices, such as CD
players, VCRs and cassette decks, are selected
using the device Input Selectors
e, these
buttons may function as Chapter Step or Track
Advance.
` Clear Button: Press this button to clear
incorrect entries when using the remote to directly
enter a radio station’s frequency.
Memory Button: Press this button to enter
a radio station into the AVR 120’s preset memory.
Once the MEMORY Indicator
O flashes, you
have five seconds to enter a preset memory
location using the Numeric Keys
r (See
page 26 for more information.)
Delay/Prev Ch.: Press this button to
begin the process for setting the delay times
used by the AVR 120 when processing surround
sound. After pressing this button, the delay
times are entered by pressing the Set Button
o and then using the
⁄ / ¤ Buttons mq
to change the setting. Press the Set Button
o again to complete the process. (See page
19 for more information.)
› Button: Press this button to change a
setting or selection when configuring many of the
AVR 120’s settings.
Speaker Select: Press this button to
begin the process of configuring the AVR
120’s bass management system for use with
the type of speakers used in your system. Once
the button has been pressed, use the
⁄ / ¤
Buttons mq to select the channel you
wish to set up. Press the Set Button o and
then select another channel to configure.
When all adjustments have been completed,
press the Set Button
o twice to exit the
settings and return to normal operation. (See
page 17 for more information.)
Spare Button: This button does not have
any function for the operation of the AVR 120,
but it is available for use when programmed
with the code from another remote. (See page
27 for information on programming the remote
with codes for other devices.)
Volume Up/Down: Press these buttons to
raise or lower the system volume. See page 29
for more information on programming the
Volume Control Punch-Through capability of
the remote, which allows you to change the
AVR 120’s volume while the remote is set to
control another device.
TV/Video Selector: This button does not
have a direct function on the AVR 120, but
when used with a compatibly programmed
VCR, DVD or satellite receiver that has a
“TV/Video” function, pressing this button will
switch between the output of the player or
receiver and the external video input to that
player. Consult the owner’s manual for your
specific player or receiver for the details of how
it implements this function.
Mute: Press this button to momentarily
silence the AVR 120 or TV set being controlled,
depending on which device has been selected.
When the AVR 120 is muted, press this button
or use the Volume Control
Ó to return
to the previous volume level. When the AVR 120
remote is being programmed to operate another
device or when a macro command is being pro-
grammed, this button is pressed with the Input
Selector Button
e to begin the program-
ming process. (See page 27 for more informa-
tion on programming the remote.)
33
35
34
33
32
31
30
29
28
Remote Control Functions