beautypg.com

Caution – HP Clemco 60 HP User Manual

Page 11

background image

APOLLO 60 HP SUPPLIED-AIR RESPIRATOR

Page 10

7.2.4

Periodically inspect and clean the foam filter and

screen in the alternate air control valve. Replace the foam
filter at first sign of blockage or deterioration. (See Section
9.8)

7.2.5

The inner collar is a very important factor in

controlling air escape from the helmet and preventing
ingress of dust. The elastic properties of the collar are
intended to provide a snug fit on the user’s neck. The collar
must be replaced before it is stretched to the point where
it no longer fits snugly around the neck.

7.2.6

The outer cape provides protection from rebound-

ing abrasive and from abrasive ingress into the helmet.
Inspect the outer cape frequently for wear. Replace the
cape before holes are worn through, or any wear occurs
that prevents the cape from providing the protection for
which it is intended.

7.3

Cleaning and Disinfecting

7.3.1

Respirators must be cleaned and disinfected as

frequently as necessary to ensure that proper protection is
provided to the wearer. Respirators used by more than one
person must be cleaned and disinfected after each use.
See Section 8.0 for cleaning instructions. [Reference
OSHA Regulations 1910.134 (b)(5); 1910.134 (f)(3)].

7.4

Repair (Service Maintenance)

7.4.1

Replacement or repairs shall be done only by

trained persons, using genuine Clemco parts designed for
the respirator. No attempt shall be made to replace com-
ponents or to make adjustment or repairs beyond the
manufacturer’s recommendations. See Sec. 9.0 for ser-
vice instructions. [Reference OSHA Regulations 1910.134
(f)(4)].

7.5

Storage

7.5.1

Daily Storage

7.5.1.1 When the respirator is not in use, it must be stored
in a clean, dry area. Hang the respirator by the strap
provided on the top. Do not tuck the cape inside the helmet.
Let the cape hang loose to allow air to circulate, to dry
condensation from the cape and from inside the helmet.

7.5.2

Long-term storage

7.5.2.1 After inspection, cleaning and thorough drying,
and after necessary repairs are made, the cape should be
tucked inside the helmet. The respirator shall then be
placed in a plastic bag and the bag sealed to keep out dust
and moisture. Place the bag in a clearly marked carton and

store it in a clean, dry place. [Reference OSHA Regula-
tions 1910.134 (f)(5)].

8.0

CLEANING

! CAUTION

Follow washing instructions as described in this
section. Do not use any caustic chemicals or
solvents that may be irritating or harmful to the
user, or which change the properties of the mate-
rials used in any part of the respirator.

8.1

Outer Cape

8.1.1

The cape can be machine washed using warm

water and mild detergent. Dry in a clothes dryer at the
lowest temperature setting. Do not dry clean. See Section
9.4 for removal and installation instructions.

8.2

Inner Collar

8.2.1

The removable inner collar should be frequently

washed to remove build-up of dirt that accumulates from
normal perspiration and air moisture. For general hygiene,
daily washing is recommended.

8.2.2

The inner collar may be either washed or replaced

separately or with the outer cape. To wash separately,
unzip the collar and machine wash with warm water and
mild detergent. Tumble dry in a clothes dryer at the lowest
temperature setting. Do not dry clean.

8.3

Sweatband and Suspension

8.3.1

The sweatband, suspension, suspension strap,

and chin strap should be washed using warm water and
mild detergent. See Section 6.2 for removing the suspen-
sion.

8.4

Helmet Assembly

8.4.1

The helmet assembly should be wiped clean with

mild detergent and water. DO NOT IMMERSE THE HEL-
MET IN WATER!
While this does not permanently dam-
age the helmet, it will require an extended drying period.

8.4.2

Care must be used to prevent abrasive entry when

putting on or removing the respirator and when changing
lenses. Vacuum the inside of the helmet to remove any
abrasive.

This manual is related to the following products: