Hitachi VT-FX795A - Manual (Page 5)

– 5 – EN
An index mark will be assigned at the beginning of
each recordings you make. You may skip to a specific
marked point by following the steps below.
1 Press [SEARCH MODE] so that the Index
Search menu appears.
2 Enter the number of recordings
you wish to skip by pressing [PLAY] or [STOP]
within 30 seconds.
3 Press [F.FWD] or [REW] to start index search. If
you want to go in the forward direction, press
[F.FWD]. If you want to go in the reverse direc-
tion, press [REW].
• After index search, the VCR will play the tape auto-
matically.
This feature allows you to go to a specific point on a
tape by entering the exact amount of time you wish to
skip in order to reach the point.
1 Press [SEARCH MODE] twice so that the Time
Search menu appears.
2 Enter your desired time to skip
by pressing [PLAY] or [STOP] within 30 seconds.
3 Press [F.FWD] or [REW] to start time search. If
you want to go in the forward direction, press
[F.FWD]. If you want to go in the reverse direc-
tion, press [REW].
• After time search, the VCR will play the tape auto-
matically.
Time Search
TIME SEARCH
2 : 50
INDEX SEARCH
03
Index Search
This feature allows you to play a tape over and over.
1 Select main menu by pressing [MENU].
2 Select "AUTO REPEAT" by pressing [PLAY] or
[STOP].
3 Begin auto repeat playback by pressing
[F.FWD] so that [ON] appears next to "AUTO
REPEAT".
• If the on-screen menu still remains, press
[COUNTER RESET/EXIT] to exit the menu.
• To cancel the Auto repeat mode, press [F.FWD] at
step [3] so that [OFF] appears next to "AUTO
REPEAT".
Auto Repeat Playback
Search Functions
If you want to skip or repeat a scene during playback,
press [F.FWD] or [REW].
• Press it again and the VCR will now search in super
high speed. (in the LP/SLP modes only)
Picture Search
– 5 – EN
This feature allows you to set the recording length sim-
ply by pressing [REC/IRT] on the VCR.
1 Begin IRT by pressing [REC/IRT] on the VCR
repeatedly until the desired recording length
appears.
IRT (Instant Recording Timer)
REC IRT(0:30) IRT(1:00).....
(Normal recording)
IRT(8:00) IRT(7:30)
It may be unlawful to record copyrighted material with-
out the consent of the copyright owner.
Accidental erasure prevention
To prevent accidental recording on a
recorded cassette, remove its record
safety tab. To record on it later, cover
the hole with cellophane tape.
Before recording, make sure:
• The desired channel is selected by pressing
[Number] on the remote control or the
[CHANNEL ]. (If you connected the VCR to a
cable box or satellite box as in "VCR to TV
Connection" on page 3, select the VCR to channel 3
or 4 the same channel as the RF output channel of
the VCR. Then, select the channel you want to record
at the cable box or satellite box. In this case, you can
ONLY record and view the SAME channel. )
• There is a tape with its safety tab into the VCR.
• The desired recording speed is selected in SP(stan-
dard play) or SLP(super long play) mode by pressing
[SPEED] on the remote control.
• TV STEREO or SAP is selected.
( )
Record safety tab
Type of tape T60 T120 T160
SP mode 1hour 2hours 2-2/3hours
SLP mode 3hours 6hours 8hours
Tape Speed Recording/Playback Time
1 Begin the recording by pressing [RECORD].
• To temporarily stop recording or resume it, press
[PAUSE]. After the VCR has been in Pause mode
for 5 minutes, it will stop automatically to protect
the tape and the video head from damage.
2 Press [STOP] when recording is completed.
RECORDING FUNCTION
Viewing and Recording the Same Program
PLAYBACK FUNCTION