haier HWM65-0566 - Manual (Page 8)

>10mm
About less than 2mm after twisting
Figure 3
Connection between the water inlet hose jointer and the water faucet
Bushing
About 4mm before twisting
2. Loosen the screw till the water faucet can be accessed. Put the jointer of the water inlet hose on the faucet.
See to Figure 2. (If the faucet is too large and the jointer can not be set on the water faucet, please loosen
the four screws and take out the bushing in the jointer. The front end of the faucet must be smooth,
otherwise it may leak water. See to Figure 3.)
1. Press the lower end of the lock lever and push down the slider. Take off the water inlet hose jointer from the
water inlet hose component. See to Figure 1.
Water faucet,not suitable
Install the water inlet hose
Screw
It is required that the front end shall be longer than 10mm.
The exit end face of the faucet shall be flat and smooth. If not please file it to avoid leakage.
remark: Before installation, the threading is 4mmabove the upper surface of the nut.
After installation, the threading is 2mm above the upper surface of the nut. See to figure 6.
Figure 6
Sign plate
4 Take off the nameplate. Twist the fastening nut as per the indication of the figure
to seal up the exit end face of the faucet. See to Figure 5.
Figure 2
Screw nut
Screw knife
3. Fasten the four screws evenly. See to Figure 4.
water inlet hose jointer
Figure 5
Outlet end surface
Slider
Figure 1
Water faucet,suitable
water inlet hose
Figure 4
Lock level
Reserve, remain time digitron
It displays "--" during detecting.
It displays remained reserve time (hour).
It displays total remained time (min).
It displays abnormal symbol in abnormal situation.
(See to Page15)
Confirm the water faucet
43 46
36
28
20
12
TUB DRY button
1 6
2 4
3 2
4 0
"Power" button
Push the "power" button to switch on the power.
Under power-on mode, push it to switch off the power.
Push the "power" button to switch on the power. If
the "start/pause" button is not pushed, the machine
will switch off the power automatically after 5 minutes.
Quick
Standard Tub dry
Jean
Normal
Fibre
Woollen
Reserve Reserve
Water
level
Water
level
Program Program
Tub
dry
Tub
dry
Po
we
r
Po
we
r
"Reserve" button
The digitron displays remain time
before washing is finished (in minutes)
Push "reserve" button, the digitron
displays the reserve time of washing
(in hours). The indicator flashes to
indicate that the reserve function
is operating.Push "reserve" button to
display the reserve mode.
WATER LEVEL button
32L and 46L.
The washing machine can detect the laundries automatically.
After detection, it will set the water level to suitable value among
24L,32L,40L,46L automatically.
You can also set water level by yourself. After the machine is started, it
will not set water level automatically. You shall push the start/pause
button to make new setting.
If there's water inside the tub, the machine cannot detect the laundries
and will display water level 32L .
If wet laundries are put in, it may display water level 46L . You must set
suitable water level by yourself.
If QUICK programs selected, it will display water level 20L .
When water level 16L is reached in water filling, it will perform
washing while filling water. When water level 20L is reached, it will
change to normal washing.
If WOOLLEN program selected,water level only can be set between
During operation of wash,soak and rinse program, you can push
down the water level button to add water. When you release the button,
or it reaches the overflow water level, the machine will stop adding
water.
The water level decided may be different from actual value because of
the different moisture level of the laundries.
PROGRAM
STANDARD
QUICK
JEAN
FIBER
WOOLLEN
NORMAL
PROGRAM selection button
Following automatic programs are available for selection
Applicable situation
Common washing
Washing the relatively big and thick laundries
Washing the chemical fiber laundries
Washing the woolen textiles
Common washing
Quick and high-efficiency wash for common
laundries
Push the"TUB DRY"button,the indicator
is lighted,and the"TUB DRY"function is
operating. After washing,the innerand
outer tub is wet,mildew may grow not
using for a long time.Then,the
"TUB DRY" fuction can make the tub dry
preventing mildew from
growing.
Notice: When "Tub Dry" have been selected,
all functions are unavailable except " Reserve" ,
the indicators of Spin, Tub Dry and Reserve
LED are lighted, and others are off.